Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

Delrin (Acetal / Polyoxymethylene / POM-C) — 3/16" (0.1875 in) 4-Flute Speeds & Feeds

ISO Group O 85 Shore D / 120 Rockwell R

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
33,422 RPM
Surface Speed: 500 m/min (1640.4 SFM)
Table Feed Rate F = RPM·z·fz
4,572 mm/min
180.5 IPM
Plunge/Ramp Rate: 1600 mm/min
Adjusted Chip Load CTF: 1.1549×
0.0342 mm/t
0.00135 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
38.85 cm³/min
2.38 in³/min
Power Required: 0.2 kW (0.27 HP)
Direct CNC Machining Solution

For milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 3/16" (0.1875 in) 4-flute TiAlN carbide end mill, the recommended spindle speed is 33,422 RPM at 500 m/min (1640.4 SFM), with a profiling feed rate of 4,572 mm/min (180.5 IPM) and adjusted chip load of 0.0342 mm/tooth, achieving a material removal rate of 38.85 cm³/min (2.38 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
Delrin (Acetal / Polyoxymethylene / POM-C) Stock CLIMB D = 4.762 mm (0.1875") ae = 1.19 mm ap = 7.14 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1549×
Spindle Torque 0.05 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (500 × 1000) / (π × 4.762) = 33,422 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 1.19/4.762 = 0.25 → CTF = 1.1549×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0296 mm × 1.1549 = 0.0342 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 33,422 × 4 × 0.0342 = 4,572 mm/min (180.5 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (7.14 × 1.19 × 4572) / 1000 = 38.85 cm³/min (2.38 in³/min)
Specific Cutting Force (kc) for Delrin (Acetal / Polyoxymethylene / POM-C): 250 N/mm². Spindle drive efficiency η = 0.80.

Delrin (Acetal / Polyoxymethylene / POM-C) (3/16" (0.1875 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 3/16" (0.1875 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 4.76 mm 2.38 mm 1× 1,484 58.2 16.81 0.09
Slotting (100% WOC) 3F 4.76 mm 2.38 mm 1× 2,226 87.2 25.22 0.13
Slotting (100% WOC) 4F 4.76 mm 2.38 mm 1× 2,968 116.3 33.62 0.18
Profiling / HEM (25% WOC) 2F 1.19 mm 7.14 mm 1.1549× 2,286 90.2 19.42 0.1
Profiling / HEM (25% WOC) 3F 1.19 mm 7.14 mm 1.1549× 3,429 135.4 29.13 0.15
Profiling / HEM (25% WOC) CURRENT 4F 1.19 mm 7.14 mm 1.1549× 4,572 180.5 38.85 0.2
Adaptive Clearing (10% WOC) 2F 0.48 mm 9.52 mm 1.6608× 3,289 129.7 15.03 0.08
Adaptive Clearing (10% WOC) 3F 0.48 mm 9.52 mm 1.6608× 4,933 194.5 22.54 0.12
Adaptive Clearing (10% WOC) 4F 0.48 mm 9.52 mm 1.6608× 6,577 259.4 30.05 0.16

Shop-Floor Machining Strategy for Delrin (Acetal / Polyoxymethylene / POM-C)

Work Hardening: None (Stress relaxation can occur; stress-relieve stock for tight tolerances)
Coolant & Lubrication Protocol

Cold Air Gun (Vortex Tube) or Light Water-Soluble Flood Coolant

Pressure: Air gun at 5 bar

Avoid chlorinated or ester coolants that degrade polymers. Continuous chip evacuation prevents localized plastic remelting.

Chip Evacuation & Tool Path Guidance

Chip Flow: Continuous plastic ribbons; high volume air evacuation required to prevent chip wrapping on spindle arbor.

Milling Direction: Climb milling produces pristine finishes.

Expert Machinist Tips:
  • High chip load is essential: chips carry away the heat. If feed is too slow, plastic melts and binds to flutes.
  • Use 1-flute (O-flute) or 2-flute upward spiral router/end mills for maximum chip clearance.
  • Avoid over-clamping in vises; Delrin flexes easily under clamping jaw pressure.

Frequently Asked CNC Questions (Delrin (Acetal / Polyoxymethylene / POM-C) / 3/16" (0.1875 in))

What is the recommended RPM for milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 3/16" (0.1875 in) end mill?
For a 3/16" (0.1875 in) (4.762 mm) TiAlN coated carbide end mill in Delrin (Acetal / Polyoxymethylene / POM-C), the baseline surface cutting speed is 500 m/min (1640.4 SFM), which translates to a calculated spindle speed of 33,422 RPM. If using uncoated carbide, reduce surface speed to 450 m/min (1500 SFM / 30080 RPM). For HSS cutters, speed must be restricted to 140 m/min (9358 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 3/16" (0.1875 in) in Delrin (Acetal / Polyoxymethylene / POM-C)?
At 33,422 RPM with a 4-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0342 mm/tooth (0.00135"/tooth) after applying a radial chip thinning factor (CTF) of 1.1549×. This yields a table feed rate of 4572 mm/min (180.5 IPM). Ramping or plunging into material should be limited to 35% of table feed (1600 mm/min / 63.2 IPM) at an entry ramp angle of 1.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 1.19 mm), the Chip Thinning Factor is 1.1549×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining Delrin (Acetal / Polyoxymethylene / POM-C)?
Cold Air Gun (Vortex Tube) or Light Water-Soluble Flood Coolant. Pressure specification: Air gun at 5 bar. Engineering rationale: Avoid chlorinated or ester coolants that degrade polymers. Continuous chip evacuation prevents localized plastic remelting.