Delrin (Acetal / Polyoxymethylene / POM-C) — 16 mm 4-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 16 mm 4-flute TiAlN carbide end mill, the recommended spindle speed is 9,947 RPM at 500 m/min (1640.4 SFM), with a profiling feed rate of 3,589 mm/min (141.2 IPM) and adjusted chip load of 0.0902 mm/tooth, achieving a material removal rate of 344.54 cm³/min (21.01 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathDelrin (Acetal / Polyoxymethylene / POM-C) (16 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 16 mm | 8 mm | 1× | 1,166 | 46 | 149.25 | 0.78 |
| Slotting (100% WOC) | 3F | 16 mm | 8 mm | 1× | 1,749 | 68.9 | 223.87 | 1.17 |
| Slotting (100% WOC) | 4F | 16 mm | 8 mm | 1× | 2,332 | 91.9 | 298.5 | 1.55 |
| Profiling / HEM (25% WOC) | 2F | 4 mm | 24 mm | 1.1547× | 1,794 | 70.6 | 172.22 | 0.9 |
| Profiling / HEM (25% WOC) | 3F | 4 mm | 24 mm | 1.1547× | 2,692 | 105.9 | 258.43 | 1.35 |
| Profiling / HEM (25% WOC) CURRENT | 4F | 4 mm | 24 mm | 1.1547× | 3,589 | 141.2 | 344.54 | 1.79 |
| Adaptive Clearing (10% WOC) | 2F | 1.6 mm | 32 mm | 1.6667× | 2,590 | 102.1 | 132.61 | 0.69 |
| Adaptive Clearing (10% WOC) | 3F | 1.6 mm | 32 mm | 1.6667× | 3,885 | 153.1 | 198.91 | 1.04 |
| Adaptive Clearing (10% WOC) | 4F | 1.6 mm | 32 mm | 1.6667× | 5,180 | 204.1 | 265.22 | 1.38 |
Shop-Floor Machining Strategy for Delrin (Acetal / Polyoxymethylene / POM-C)
Work Hardening: None (Stress relaxation can occur; stress-relieve stock for tight tolerances)Cold Air Gun (Vortex Tube) or Light Water-Soluble Flood Coolant
Pressure: Air gun at 5 bar
Avoid chlorinated or ester coolants that degrade polymers. Continuous chip evacuation prevents localized plastic remelting.
Chip Flow: Continuous plastic ribbons; high volume air evacuation required to prevent chip wrapping on spindle arbor.
Milling Direction: Climb milling produces pristine finishes.
- High chip load is essential: chips carry away the heat. If feed is too slow, plastic melts and binds to flutes.
- Use 1-flute (O-flute) or 2-flute upward spiral router/end mills for maximum chip clearance.
- Avoid over-clamping in vises; Delrin flexes easily under clamping jaw pressure.
Frequently Asked CNC Questions (Delrin (Acetal / Polyoxymethylene / POM-C) / 16 mm)
What is the recommended RPM for milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 16 mm end mill?
What table feed rate and chip load should I program for 16 mm in Delrin (Acetal / Polyoxymethylene / POM-C)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining Delrin (Acetal / Polyoxymethylene / POM-C)?
Recent Calculations
No recent calculations saved yet.