Delrin (Acetal / Polyoxymethylene / POM-C) — 2 mm 2-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 2 mm 2-flute TiAlN carbide end mill, the recommended spindle speed is 79,577 RPM at 500 m/min (1640.4 SFM), with a profiling feed rate of 2,722 mm/min (106.6 IPM) and adjusted chip load of 0.0171 mm/tooth, achieving a material removal rate of 4.08 cm³/min (0.25 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathDelrin (Acetal / Polyoxymethylene / POM-C) (2 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 2 mm | 1 mm | 1× | 1,767 | 70 | 3.53 | 0.02 |
| Slotting (100% WOC) | 3F | 2 mm | 1 mm | 1× | 2,650 | 105 | 5.3 | 0.03 |
| Slotting (100% WOC) | 4F | 2 mm | 1 mm | 1× | 3,533 | 140.1 | 7.07 | 0.04 |
| Profiling / HEM (25% WOC) CURRENT | 2F | 0.5 mm | 3 mm | 1.1547× | 2,722 | 106.6 | 4.08 | 0.02 |
| Profiling / HEM (25% WOC) | 3F | 0.5 mm | 3 mm | 1.1547× | 4,082 | 159.9 | 6.12 | 0.03 |
| Profiling / HEM (25% WOC) | 4F | 0.5 mm | 3 mm | 1.1547× | 5,443 | 213.3 | 8.16 | 0.04 |
| Adaptive Clearing (10% WOC) | 2F | 0.2 mm | 4 mm | 1.6667× | 3,931 | 154.4 | 3.14 | 0.02 |
| Adaptive Clearing (10% WOC) | 3F | 0.2 mm | 4 mm | 1.6667× | 5,897 | 231.6 | 4.72 | 0.02 |
| Adaptive Clearing (10% WOC) | 4F | 0.2 mm | 4 mm | 1.6667× | 7,862 | 308.8 | 6.29 | 0.03 |
Shop-Floor Machining Strategy for Delrin (Acetal / Polyoxymethylene / POM-C)
Work Hardening: None (Stress relaxation can occur; stress-relieve stock for tight tolerances)Cold Air Gun (Vortex Tube) or Light Water-Soluble Flood Coolant
Pressure: Air gun at 5 bar
Avoid chlorinated or ester coolants that degrade polymers. Continuous chip evacuation prevents localized plastic remelting.
Chip Flow: Continuous plastic ribbons; high volume air evacuation required to prevent chip wrapping on spindle arbor.
Milling Direction: Climb milling produces pristine finishes.
- High chip load is essential: chips carry away the heat. If feed is too slow, plastic melts and binds to flutes.
- Use 1-flute (O-flute) or 2-flute upward spiral router/end mills for maximum chip clearance.
- Avoid over-clamping in vises; Delrin flexes easily under clamping jaw pressure.
Frequently Asked CNC Questions (Delrin (Acetal / Polyoxymethylene / POM-C) / 2 mm)
What is the recommended RPM for milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 2 mm end mill?
What table feed rate and chip load should I program for 2 mm in Delrin (Acetal / Polyoxymethylene / POM-C)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining Delrin (Acetal / Polyoxymethylene / POM-C)?
Recent Calculations
No recent calculations saved yet.