Delrin (Acetal / Polyoxymethylene / POM-C) — 4 mm 3-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 4 mm 3-flute TiAlN carbide end mill, the recommended spindle speed is 39,789 RPM at 500 m/min (1640.4 SFM), with a profiling feed rate of 3,557 mm/min (139.7 IPM) and adjusted chip load of 0.0298 mm/tooth, achieving a material removal rate of 21.34 cm³/min (1.3 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathDelrin (Acetal / Polyoxymethylene / POM-C) (4 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 4 mm | 2 mm | 1× | 1,536 | 60.5 | 12.29 | 0.06 |
| Slotting (100% WOC) | 3F | 4 mm | 2 mm | 1× | 2,304 | 90.7 | 18.43 | 0.1 |
| Slotting (100% WOC) | 4F | 4 mm | 2 mm | 1× | 3,072 | 121 | 24.58 | 0.13 |
| Profiling / HEM (25% WOC) | 2F | 1 mm | 6 mm | 1.1547× | 2,371 | 93.1 | 14.23 | 0.07 |
| Profiling / HEM (25% WOC) CURRENT | 3F | 1 mm | 6 mm | 1.1547× | 3,557 | 139.7 | 21.34 | 0.11 |
| Profiling / HEM (25% WOC) | 4F | 1 mm | 6 mm | 1.1547× | 4,743 | 186.2 | 28.46 | 0.15 |
| Adaptive Clearing (10% WOC) | 2F | 0.4 mm | 8 mm | 1.6667× | 3,422 | 134.5 | 10.95 | 0.06 |
| Adaptive Clearing (10% WOC) | 3F | 0.4 mm | 8 mm | 1.6667× | 5,133 | 201.7 | 16.43 | 0.09 |
| Adaptive Clearing (10% WOC) | 4F | 0.4 mm | 8 mm | 1.6667× | 6,844 | 269 | 21.9 | 0.11 |
Shop-Floor Machining Strategy for Delrin (Acetal / Polyoxymethylene / POM-C)
Work Hardening: None (Stress relaxation can occur; stress-relieve stock for tight tolerances)Cold Air Gun (Vortex Tube) or Light Water-Soluble Flood Coolant
Pressure: Air gun at 5 bar
Avoid chlorinated or ester coolants that degrade polymers. Continuous chip evacuation prevents localized plastic remelting.
Chip Flow: Continuous plastic ribbons; high volume air evacuation required to prevent chip wrapping on spindle arbor.
Milling Direction: Climb milling produces pristine finishes.
- High chip load is essential: chips carry away the heat. If feed is too slow, plastic melts and binds to flutes.
- Use 1-flute (O-flute) or 2-flute upward spiral router/end mills for maximum chip clearance.
- Avoid over-clamping in vises; Delrin flexes easily under clamping jaw pressure.
Frequently Asked CNC Questions (Delrin (Acetal / Polyoxymethylene / POM-C) / 4 mm)
What is the recommended RPM for milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 4 mm end mill?
What table feed rate and chip load should I program for 4 mm in Delrin (Acetal / Polyoxymethylene / POM-C)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining Delrin (Acetal / Polyoxymethylene / POM-C)?
Recent Calculations
No recent calculations saved yet.