Delrin (Acetal / Polyoxymethylene / POM-C) — 8 mm 4-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 8 mm 4-flute TiAlN carbide end mill, the recommended spindle speed is 19,894 RPM at 500 m/min (1640.4 SFM), with a profiling feed rate of 4,122 mm/min (162.3 IPM) and adjusted chip load of 0.0518 mm/tooth, achieving a material removal rate of 98.93 cm³/min (6.03 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathDelrin (Acetal / Polyoxymethylene / POM-C) (8 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 8 mm | 4 mm | 1× | 1,337 | 52.5 | 42.78 | 0.22 |
| Slotting (100% WOC) | 3F | 8 mm | 4 mm | 1× | 2,005 | 78.8 | 64.16 | 0.33 |
| Slotting (100% WOC) | 4F | 8 mm | 4 mm | 1× | 2,674 | 105 | 85.57 | 0.45 |
| Profiling / HEM (25% WOC) | 2F | 2 mm | 12 mm | 1.1547× | 2,061 | 81.2 | 49.46 | 0.26 |
| Profiling / HEM (25% WOC) | 3F | 2 mm | 12 mm | 1.1547× | 3,092 | 121.8 | 74.21 | 0.39 |
| Profiling / HEM (25% WOC) CURRENT | 4F | 2 mm | 12 mm | 1.1547× | 4,122 | 162.3 | 98.93 | 0.52 |
| Adaptive Clearing (10% WOC) | 2F | 0.8 mm | 16 mm | 1.6667× | 2,976 | 117 | 38.09 | 0.2 |
| Adaptive Clearing (10% WOC) | 3F | 0.8 mm | 16 mm | 1.6667× | 4,464 | 175.5 | 57.14 | 0.3 |
| Adaptive Clearing (10% WOC) | 4F | 0.8 mm | 16 mm | 1.6667× | 5,952 | 234 | 76.19 | 0.4 |
Shop-Floor Machining Strategy for Delrin (Acetal / Polyoxymethylene / POM-C)
Work Hardening: None (Stress relaxation can occur; stress-relieve stock for tight tolerances)Cold Air Gun (Vortex Tube) or Light Water-Soluble Flood Coolant
Pressure: Air gun at 5 bar
Avoid chlorinated or ester coolants that degrade polymers. Continuous chip evacuation prevents localized plastic remelting.
Chip Flow: Continuous plastic ribbons; high volume air evacuation required to prevent chip wrapping on spindle arbor.
Milling Direction: Climb milling produces pristine finishes.
- High chip load is essential: chips carry away the heat. If feed is too slow, plastic melts and binds to flutes.
- Use 1-flute (O-flute) or 2-flute upward spiral router/end mills for maximum chip clearance.
- Avoid over-clamping in vises; Delrin flexes easily under clamping jaw pressure.
Frequently Asked CNC Questions (Delrin (Acetal / Polyoxymethylene / POM-C) / 8 mm)
What is the recommended RPM for milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 8 mm end mill?
What table feed rate and chip load should I program for 8 mm in Delrin (Acetal / Polyoxymethylene / POM-C)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining Delrin (Acetal / Polyoxymethylene / POM-C)?
Recent Calculations
No recent calculations saved yet.