Delrin (Acetal / Polyoxymethylene / POM-C) — 6 mm 4-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 6 mm 4-flute TiAlN carbide end mill, the recommended spindle speed is 26,526 RPM at 500 m/min (1640.4 SFM), with a profiling feed rate of 4,361 mm/min (171.9 IPM) and adjusted chip load of 0.0411 mm/tooth, achieving a material removal rate of 58.87 cm³/min (3.6 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathDelrin (Acetal / Polyoxymethylene / POM-C) (6 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 6 mm | 3 mm | 1× | 1,416 | 55.7 | 25.49 | 0.13 |
| Slotting (100% WOC) | 3F | 6 mm | 3 mm | 1× | 2,125 | 83.6 | 38.25 | 0.2 |
| Slotting (100% WOC) | 4F | 6 mm | 3 mm | 1× | 2,833 | 111.4 | 50.99 | 0.27 |
| Profiling / HEM (25% WOC) | 2F | 1.5 mm | 9 mm | 1.1547× | 2,180 | 85.9 | 29.43 | 0.15 |
| Profiling / HEM (25% WOC) | 3F | 1.5 mm | 9 mm | 1.1547× | 3,271 | 128.9 | 44.16 | 0.23 |
| Profiling / HEM (25% WOC) CURRENT | 4F | 1.5 mm | 9 mm | 1.1547× | 4,361 | 171.9 | 58.87 | 0.31 |
| Adaptive Clearing (10% WOC) | 2F | 0.6 mm | 12 mm | 1.6667× | 3,146 | 123.6 | 22.65 | 0.12 |
| Adaptive Clearing (10% WOC) | 3F | 0.6 mm | 12 mm | 1.6667× | 4,719 | 185.4 | 33.98 | 0.18 |
| Adaptive Clearing (10% WOC) | 4F | 0.6 mm | 12 mm | 1.6667× | 6,292 | 247.2 | 45.3 | 0.24 |
Shop-Floor Machining Strategy for Delrin (Acetal / Polyoxymethylene / POM-C)
Work Hardening: None (Stress relaxation can occur; stress-relieve stock for tight tolerances)Cold Air Gun (Vortex Tube) or Light Water-Soluble Flood Coolant
Pressure: Air gun at 5 bar
Avoid chlorinated or ester coolants that degrade polymers. Continuous chip evacuation prevents localized plastic remelting.
Chip Flow: Continuous plastic ribbons; high volume air evacuation required to prevent chip wrapping on spindle arbor.
Milling Direction: Climb milling produces pristine finishes.
- High chip load is essential: chips carry away the heat. If feed is too slow, plastic melts and binds to flutes.
- Use 1-flute (O-flute) or 2-flute upward spiral router/end mills for maximum chip clearance.
- Avoid over-clamping in vises; Delrin flexes easily under clamping jaw pressure.
Frequently Asked CNC Questions (Delrin (Acetal / Polyoxymethylene / POM-C) / 6 mm)
What is the recommended RPM for milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 6 mm end mill?
What table feed rate and chip load should I program for 6 mm in Delrin (Acetal / Polyoxymethylene / POM-C)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining Delrin (Acetal / Polyoxymethylene / POM-C)?
Recent Calculations
No recent calculations saved yet.