HDPE (High-Density Polyethylene) — 1/2" (0.500 in) 3-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling HDPE (High-Density Polyethylene) with a 1/2" (0.500 in) 3-flute TiAlN carbide end mill, the recommended spindle speed is 11,279 RPM at 450 m/min (1476.4 SFM), with a profiling feed rate of 2,690 mm/min (105.9 IPM) and adjusted chip load of 0.0795 mm/tooth, achieving a material removal rate of 162.45 cm³/min (9.91 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathHDPE (High-Density Polyethylene) (1/2" (0.500 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 12.7 mm | 6.35 mm | 1× | 1,164 | 45.8 | 93.87 | 0.35 |
| Slotting (100% WOC) | 3F | 12.7 mm | 6.35 mm | 1× | 1,746 | 68.7 | 140.81 | 0.53 |
| Slotting (100% WOC) | 4F | 12.7 mm | 6.35 mm | 1× | 2,328 | 91.6 | 187.74 | 0.7 |
| Profiling / HEM (25% WOC) | 2F | 3.17 mm | 19.05 mm | 1.1553× | 1,793 | 70.6 | 108.28 | 0.41 |
| Profiling / HEM (25% WOC) CURRENT | 3F | 3.17 mm | 19.05 mm | 1.1553× | 2,690 | 105.9 | 162.45 | 0.61 |
| Profiling / HEM (25% WOC) | 4F | 3.17 mm | 19.05 mm | 1.1553× | 3,587 | 141.2 | 216.61 | 0.81 |
| Adaptive Clearing (10% WOC) | 2F | 1.27 mm | 25.4 mm | 1.6667× | 2,587 | 102 | 83.45 | 0.31 |
| Adaptive Clearing (10% WOC) | 3F | 1.27 mm | 25.4 mm | 1.6667× | 3,881 | 152.9 | 125.19 | 0.47 |
| Adaptive Clearing (10% WOC) | 4F | 1.27 mm | 25.4 mm | 1.6667× | 5,175 | 203.9 | 166.94 | 0.63 |
Shop-Floor Machining Strategy for HDPE (High-Density Polyethylene)
Work Hardening: None (Significant thermal expansion coefficient: 10x of steel)Cold Compressed Air Blast or Water Mist
Pressure: 5 bar compressed air
HDPE melts at only 130°C (266°F). Cold air blast is mandatory to prevent gumming.
Chip Flow: Produces fluffy, lightweight, static-charged continuous shavings. High volume vacuum extraction recommended.
Milling Direction: Climb milling prevents feathered edge tears.
- Use razor-sharp single flute O-flute cutters with polished gullets.
- Account for thermal contraction: warm parts measured straight off the CNC machine will shrink when cooled to 20°C room temp.
- Do not allow tool to dwell or friction will melt a pocket into the plastic.
Frequently Asked CNC Questions (HDPE (High-Density Polyethylene) / 1/2" (0.500 in))
What is the recommended RPM for milling HDPE (High-Density Polyethylene) with a 1/2" (0.500 in) end mill?
What table feed rate and chip load should I program for 1/2" (0.500 in) in HDPE (High-Density Polyethylene)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining HDPE (High-Density Polyethylene)?
Recent Calculations
No recent calculations saved yet.