Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

HDPE (High-Density Polyethylene) — 1/4" (0.250 in) 3-Flute Speeds & Feeds

ISO Group O 68 Shore D / 65 Rockwell R

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
22,557 RPM
Surface Speed: 450 m/min (1476.4 SFM)
Table Feed Rate F = RPM·z·fz
3,086 mm/min
121.8 IPM
Plunge/Ramp Rate: 1080 mm/min
Adjusted Chip Load CTF: 1.1541×
0.0456 mm/t
0.0018 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
46.71 cm³/min
2.86 in³/min
Power Required: 0.18 kW (0.23 HP)
Direct CNC Machining Solution

For milling HDPE (High-Density Polyethylene) with a 1/4" (0.250 in) 3-flute TiAlN carbide end mill, the recommended spindle speed is 22,557 RPM at 450 m/min (1476.4 SFM), with a profiling feed rate of 3,086 mm/min (121.8 IPM) and adjusted chip load of 0.0456 mm/tooth, achieving a material removal rate of 46.71 cm³/min (2.86 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
HDPE (High-Density Polyethylene) Stock CLIMB D = 6.35 mm (0.25") ae = 1.59 mm ap = 9.52 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1541×
Spindle Torque 0.06 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (450 × 1000) / (π × 6.35) = 22,557 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 1.59/6.35 = 0.25 → CTF = 1.1541×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0395 mm × 1.1541 = 0.0456 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 22,557 × 3 × 0.0456 = 3,086 mm/min (121.8 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (9.52 × 1.59 × 3086) / 1000 = 46.71 cm³/min (2.86 in³/min)
Specific Cutting Force (kc) for HDPE (High-Density Polyethylene): 180 N/mm². Spindle drive efficiency η = 0.80.

HDPE (High-Density Polyethylene) (1/4" (0.250 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 1/4" (0.250 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 6.35 mm 3.17 mm 1× 1,335 52.8 26.87 0.1
Slotting (100% WOC) 3F 6.35 mm 3.17 mm 1× 2,003 79.2 40.32 0.15
Slotting (100% WOC) 4F 6.35 mm 3.17 mm 1× 2,671 105.6 53.77 0.2
Profiling / HEM (25% WOC) 2F 1.59 mm 9.52 mm 1.1541× 2,057 81.2 31.14 0.12
Profiling / HEM (25% WOC) CURRENT 3F 1.59 mm 9.52 mm 1.1541× 3,086 121.8 46.71 0.18
Profiling / HEM (25% WOC) 4F 1.59 mm 9.52 mm 1.1541× 4,114 162.4 62.27 0.23
Adaptive Clearing (10% WOC) 2F 0.64 mm 12.7 mm 1.6609× 2,959 116.4 24.05 0.09
Adaptive Clearing (10% WOC) 3F 0.64 mm 12.7 mm 1.6609× 4,439 174.6 36.08 0.14
Adaptive Clearing (10% WOC) 4F 0.64 mm 12.7 mm 1.6609× 5,919 232.8 48.11 0.18

Shop-Floor Machining Strategy for HDPE (High-Density Polyethylene)

Work Hardening: None (Significant thermal expansion coefficient: 10x of steel)
Coolant & Lubrication Protocol

Cold Compressed Air Blast or Water Mist

Pressure: 5 bar compressed air

HDPE melts at only 130°C (266°F). Cold air blast is mandatory to prevent gumming.

Chip Evacuation & Tool Path Guidance

Chip Flow: Produces fluffy, lightweight, static-charged continuous shavings. High volume vacuum extraction recommended.

Milling Direction: Climb milling prevents feathered edge tears.

Expert Machinist Tips:
  • Use razor-sharp single flute O-flute cutters with polished gullets.
  • Account for thermal contraction: warm parts measured straight off the CNC machine will shrink when cooled to 20°C room temp.
  • Do not allow tool to dwell or friction will melt a pocket into the plastic.

Frequently Asked CNC Questions (HDPE (High-Density Polyethylene) / 1/4" (0.250 in))

What is the recommended RPM for milling HDPE (High-Density Polyethylene) with a 1/4" (0.250 in) end mill?
For a 1/4" (0.250 in) (6.35 mm) TiAlN coated carbide end mill in HDPE (High-Density Polyethylene), the baseline surface cutting speed is 450 m/min (1476.4 SFM), which translates to a calculated spindle speed of 22,557 RPM. If using uncoated carbide, reduce surface speed to 400 m/min (1300 SFM / 20051 RPM). For HSS cutters, speed must be restricted to 120 m/min (6015 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 1/4" (0.250 in) in HDPE (High-Density Polyethylene)?
At 22,557 RPM with a 3-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0456 mm/tooth (0.0018"/tooth) after applying a radial chip thinning factor (CTF) of 1.1541×. This yields a table feed rate of 3086 mm/min (121.8 IPM). Ramping or plunging into material should be limited to 35% of table feed (1080 mm/min / 42.6 IPM) at an entry ramp angle of 2.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 1.59 mm), the Chip Thinning Factor is 1.1541×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining HDPE (High-Density Polyethylene)?
Cold Compressed Air Blast or Water Mist. Pressure specification: 5 bar compressed air. Engineering rationale: HDPE melts at only 130°C (266°F). Cold air blast is mandatory to prevent gumming.