HDPE (High-Density Polyethylene) — 1/4" (0.250 in) 2-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling HDPE (High-Density Polyethylene) with a 1/4" (0.250 in) 2-flute TiAlN carbide end mill, the recommended spindle speed is 22,557 RPM at 450 m/min (1476.4 SFM), with a profiling feed rate of 2,057 mm/min (81.2 IPM) and adjusted chip load of 0.0456 mm/tooth, achieving a material removal rate of 31.14 cm³/min (1.91 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathHDPE (High-Density Polyethylene) (1/4" (0.250 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 6.35 mm | 3.17 mm | 1× | 1,335 | 52.8 | 26.87 | 0.1 |
| Slotting (100% WOC) | 3F | 6.35 mm | 3.17 mm | 1× | 2,003 | 79.2 | 40.32 | 0.15 |
| Slotting (100% WOC) | 4F | 6.35 mm | 3.17 mm | 1× | 2,671 | 105.6 | 53.77 | 0.2 |
| Profiling / HEM (25% WOC) CURRENT | 2F | 1.59 mm | 9.52 mm | 1.1541× | 2,057 | 81.2 | 31.14 | 0.12 |
| Profiling / HEM (25% WOC) | 3F | 1.59 mm | 9.52 mm | 1.1541× | 3,086 | 121.8 | 46.71 | 0.18 |
| Profiling / HEM (25% WOC) | 4F | 1.59 mm | 9.52 mm | 1.1541× | 4,114 | 162.4 | 62.27 | 0.23 |
| Adaptive Clearing (10% WOC) | 2F | 0.64 mm | 12.7 mm | 1.6609× | 2,959 | 116.4 | 24.05 | 0.09 |
| Adaptive Clearing (10% WOC) | 3F | 0.64 mm | 12.7 mm | 1.6609× | 4,439 | 174.6 | 36.08 | 0.14 |
| Adaptive Clearing (10% WOC) | 4F | 0.64 mm | 12.7 mm | 1.6609× | 5,919 | 232.8 | 48.11 | 0.18 |
Shop-Floor Machining Strategy for HDPE (High-Density Polyethylene)
Work Hardening: None (Significant thermal expansion coefficient: 10x of steel)Cold Compressed Air Blast or Water Mist
Pressure: 5 bar compressed air
HDPE melts at only 130°C (266°F). Cold air blast is mandatory to prevent gumming.
Chip Flow: Produces fluffy, lightweight, static-charged continuous shavings. High volume vacuum extraction recommended.
Milling Direction: Climb milling prevents feathered edge tears.
- Use razor-sharp single flute O-flute cutters with polished gullets.
- Account for thermal contraction: warm parts measured straight off the CNC machine will shrink when cooled to 20°C room temp.
- Do not allow tool to dwell or friction will melt a pocket into the plastic.
Frequently Asked CNC Questions (HDPE (High-Density Polyethylene) / 1/4" (0.250 in))
What is the recommended RPM for milling HDPE (High-Density Polyethylene) with a 1/4" (0.250 in) end mill?
What table feed rate and chip load should I program for 1/4" (0.250 in) in HDPE (High-Density Polyethylene)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining HDPE (High-Density Polyethylene)?
Recent Calculations
No recent calculations saved yet.