Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

HDPE (High-Density Polyethylene) — 10 mm 3-Flute Speeds & Feeds

ISO Group O 68 Shore D / 65 Rockwell R

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
14,324 RPM
Surface Speed: 450 m/min (1476.4 SFM)
Table Feed Rate F = RPM·z·fz
2,819 mm/min
110.9 IPM
Plunge/Ramp Rate: 987 mm/min
Adjusted Chip Load CTF: 1.1547×
0.0656 mm/t
0.00258 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
105.71 cm³/min
6.44 in³/min
Power Required: 0.4 kW (0.53 HP)
Direct CNC Machining Solution

For milling HDPE (High-Density Polyethylene) with a 10 mm 3-flute TiAlN carbide end mill, the recommended spindle speed is 14,324 RPM at 450 m/min (1476.4 SFM), with a profiling feed rate of 2,819 mm/min (110.9 IPM) and adjusted chip load of 0.0656 mm/tooth, achieving a material removal rate of 105.71 cm³/min (6.44 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
HDPE (High-Density Polyethylene) Stock CLIMB D = 10 mm (0.3937") ae = 2.5 mm ap = 15 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1547×
Spindle Torque 0.21 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (450 × 1000) / (π × 10) = 14,324 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 2.5/10 = 0.25 → CTF = 1.1547×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0568 mm × 1.1547 = 0.0656 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 14,324 × 3 × 0.0656 = 2,819 mm/min (110.9 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (15 × 2.5 × 2819) / 1000 = 105.71 cm³/min (6.44 in³/min)
Specific Cutting Force (kc) for HDPE (High-Density Polyethylene): 180 N/mm². Spindle drive efficiency η = 0.80.

HDPE (High-Density Polyethylene) (10 mm) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 10 mm
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 10 mm 5 mm 1× 1,220 48.1 61 0.23
Slotting (100% WOC) 3F 10 mm 5 mm 1× 1,831 72.2 91.55 0.34
Slotting (100% WOC) 4F 10 mm 5 mm 1× 2,441 96.3 122.05 0.46
Profiling / HEM (25% WOC) 2F 2.5 mm 15 mm 1.1547× 1,879 73.9 70.46 0.26
Profiling / HEM (25% WOC) CURRENT 3F 2.5 mm 15 mm 1.1547× 2,819 110.9 105.71 0.4
Profiling / HEM (25% WOC) 4F 2.5 mm 15 mm 1.1547× 3,759 147.8 140.96 0.53
Adaptive Clearing (10% WOC) 2F 1 mm 20 mm 1.6667× 2,713 106.9 54.26 0.2
Adaptive Clearing (10% WOC) 3F 1 mm 20 mm 1.6667× 4,069 160.3 81.38 0.31
Adaptive Clearing (10% WOC) 4F 1 mm 20 mm 1.6667× 5,426 213.7 108.52 0.41

Shop-Floor Machining Strategy for HDPE (High-Density Polyethylene)

Work Hardening: None (Significant thermal expansion coefficient: 10x of steel)
Coolant & Lubrication Protocol

Cold Compressed Air Blast or Water Mist

Pressure: 5 bar compressed air

HDPE melts at only 130°C (266°F). Cold air blast is mandatory to prevent gumming.

Chip Evacuation & Tool Path Guidance

Chip Flow: Produces fluffy, lightweight, static-charged continuous shavings. High volume vacuum extraction recommended.

Milling Direction: Climb milling prevents feathered edge tears.

Expert Machinist Tips:
  • Use razor-sharp single flute O-flute cutters with polished gullets.
  • Account for thermal contraction: warm parts measured straight off the CNC machine will shrink when cooled to 20°C room temp.
  • Do not allow tool to dwell or friction will melt a pocket into the plastic.

Frequently Asked CNC Questions (HDPE (High-Density Polyethylene) / 10 mm)

What is the recommended RPM for milling HDPE (High-Density Polyethylene) with a 10 mm end mill?
For a 10 mm (10 mm) TiAlN coated carbide end mill in HDPE (High-Density Polyethylene), the baseline surface cutting speed is 450 m/min (1476.4 SFM), which translates to a calculated spindle speed of 14,324 RPM. If using uncoated carbide, reduce surface speed to 400 m/min (1300 SFM / 12732 RPM). For HSS cutters, speed must be restricted to 120 m/min (3820 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 10 mm in HDPE (High-Density Polyethylene)?
At 14,324 RPM with a 3-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0656 mm/tooth (0.00258"/tooth) after applying a radial chip thinning factor (CTF) of 1.1547×. This yields a table feed rate of 2819 mm/min (110.9 IPM). Ramping or plunging into material should be limited to 35% of table feed (987 mm/min / 38.8 IPM) at an entry ramp angle of 2.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 2.5 mm), the Chip Thinning Factor is 1.1547×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining HDPE (High-Density Polyethylene)?
Cold Compressed Air Blast or Water Mist. Pressure specification: 5 bar compressed air. Engineering rationale: HDPE melts at only 130°C (266°F). Cold air blast is mandatory to prevent gumming.