HDPE (High-Density Polyethylene) — 10 mm 4-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling HDPE (High-Density Polyethylene) with a 10 mm 4-flute TiAlN carbide end mill, the recommended spindle speed is 14,324 RPM at 450 m/min (1476.4 SFM), with a profiling feed rate of 3,759 mm/min (147.8 IPM) and adjusted chip load of 0.0656 mm/tooth, achieving a material removal rate of 140.96 cm³/min (8.59 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathHDPE (High-Density Polyethylene) (10 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 10 mm | 5 mm | 1× | 1,220 | 48.1 | 61 | 0.23 |
| Slotting (100% WOC) | 3F | 10 mm | 5 mm | 1× | 1,831 | 72.2 | 91.55 | 0.34 |
| Slotting (100% WOC) | 4F | 10 mm | 5 mm | 1× | 2,441 | 96.3 | 122.05 | 0.46 |
| Profiling / HEM (25% WOC) | 2F | 2.5 mm | 15 mm | 1.1547× | 1,879 | 73.9 | 70.46 | 0.26 |
| Profiling / HEM (25% WOC) | 3F | 2.5 mm | 15 mm | 1.1547× | 2,819 | 110.9 | 105.71 | 0.4 |
| Profiling / HEM (25% WOC) CURRENT | 4F | 2.5 mm | 15 mm | 1.1547× | 3,759 | 147.8 | 140.96 | 0.53 |
| Adaptive Clearing (10% WOC) | 2F | 1 mm | 20 mm | 1.6667× | 2,713 | 106.9 | 54.26 | 0.2 |
| Adaptive Clearing (10% WOC) | 3F | 1 mm | 20 mm | 1.6667× | 4,069 | 160.3 | 81.38 | 0.31 |
| Adaptive Clearing (10% WOC) | 4F | 1 mm | 20 mm | 1.6667× | 5,426 | 213.7 | 108.52 | 0.41 |
Shop-Floor Machining Strategy for HDPE (High-Density Polyethylene)
Work Hardening: None (Significant thermal expansion coefficient: 10x of steel)Cold Compressed Air Blast or Water Mist
Pressure: 5 bar compressed air
HDPE melts at only 130°C (266°F). Cold air blast is mandatory to prevent gumming.
Chip Flow: Produces fluffy, lightweight, static-charged continuous shavings. High volume vacuum extraction recommended.
Milling Direction: Climb milling prevents feathered edge tears.
- Use razor-sharp single flute O-flute cutters with polished gullets.
- Account for thermal contraction: warm parts measured straight off the CNC machine will shrink when cooled to 20°C room temp.
- Do not allow tool to dwell or friction will melt a pocket into the plastic.
Frequently Asked CNC Questions (HDPE (High-Density Polyethylene) / 10 mm)
What is the recommended RPM for milling HDPE (High-Density Polyethylene) with a 10 mm end mill?
What table feed rate and chip load should I program for 10 mm in HDPE (High-Density Polyethylene)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining HDPE (High-Density Polyethylene)?
Recent Calculations
No recent calculations saved yet.