HDPE (High-Density Polyethylene) — 16 mm 4-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling HDPE (High-Density Polyethylene) with a 16 mm 4-flute TiAlN carbide end mill, the recommended spindle speed is 8,952 RPM at 450 m/min (1476.4 SFM), with a profiling feed rate of 3,420 mm/min (134.6 IPM) and adjusted chip load of 0.0955 mm/tooth, achieving a material removal rate of 328.32 cm³/min (20.03 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathHDPE (High-Density Polyethylene) (16 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 16 mm | 8 mm | 1× | 1,110 | 43.7 | 142.08 | 0.53 |
| Slotting (100% WOC) | 3F | 16 mm | 8 mm | 1× | 1,665 | 65.5 | 213.12 | 0.8 |
| Slotting (100% WOC) | 4F | 16 mm | 8 mm | 1× | 2,220 | 87.4 | 284.16 | 1.07 |
| Profiling / HEM (25% WOC) | 2F | 4 mm | 24 mm | 1.1547× | 1,710 | 67.3 | 164.16 | 0.62 |
| Profiling / HEM (25% WOC) | 3F | 4 mm | 24 mm | 1.1547× | 2,565 | 101 | 246.24 | 0.92 |
| Profiling / HEM (25% WOC) CURRENT | 4F | 4 mm | 24 mm | 1.1547× | 3,420 | 134.6 | 328.32 | 1.23 |
| Adaptive Clearing (10% WOC) | 2F | 1.6 mm | 32 mm | 1.6667× | 2,467 | 97.2 | 126.31 | 0.47 |
| Adaptive Clearing (10% WOC) | 3F | 1.6 mm | 32 mm | 1.6667× | 3,701 | 145.8 | 189.49 | 0.71 |
| Adaptive Clearing (10% WOC) | 4F | 1.6 mm | 32 mm | 1.6667× | 4,934 | 194.4 | 252.62 | 0.95 |
Shop-Floor Machining Strategy for HDPE (High-Density Polyethylene)
Work Hardening: None (Significant thermal expansion coefficient: 10x of steel)Cold Compressed Air Blast or Water Mist
Pressure: 5 bar compressed air
HDPE melts at only 130°C (266°F). Cold air blast is mandatory to prevent gumming.
Chip Flow: Produces fluffy, lightweight, static-charged continuous shavings. High volume vacuum extraction recommended.
Milling Direction: Climb milling prevents feathered edge tears.
- Use razor-sharp single flute O-flute cutters with polished gullets.
- Account for thermal contraction: warm parts measured straight off the CNC machine will shrink when cooled to 20°C room temp.
- Do not allow tool to dwell or friction will melt a pocket into the plastic.
Frequently Asked CNC Questions (HDPE (High-Density Polyethylene) / 16 mm)
What is the recommended RPM for milling HDPE (High-Density Polyethylene) with a 16 mm end mill?
What table feed rate and chip load should I program for 16 mm in HDPE (High-Density Polyethylene)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining HDPE (High-Density Polyethylene)?
Recent Calculations
No recent calculations saved yet.