Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

HDPE (High-Density Polyethylene) — 2 mm 4-Flute Speeds & Feeds

ISO Group O 68 Shore D / 65 Rockwell R

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
71,620 RPM
Surface Speed: 450 m/min (1476.4 SFM)
Table Feed Rate F = RPM·z·fz
5,185 mm/min
203.4 IPM
Plunge/Ramp Rate: 1815 mm/min
Adjusted Chip Load CTF: 1.1547×
0.0181 mm/t
0.00071 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
7.78 cm³/min
0.47 in³/min
Power Required: 0.03 kW (0.04 HP)
Direct CNC Machining Solution

For milling HDPE (High-Density Polyethylene) with a 2 mm 4-flute TiAlN carbide end mill, the recommended spindle speed is 71,620 RPM at 450 m/min (1476.4 SFM), with a profiling feed rate of 5,185 mm/min (203.4 IPM) and adjusted chip load of 0.0181 mm/tooth, achieving a material removal rate of 7.78 cm³/min (0.47 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
HDPE (High-Density Polyethylene) Stock CLIMB D = 2 mm (0.0787") ae = 0.5 mm ap = 3 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1547×
Spindle Torque 0 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (450 × 1000) / (π × 2) = 71,620 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 0.5/2 = 0.25 → CTF = 1.1547×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0157 mm × 1.1547 = 0.0181 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 71,620 × 4 × 0.0181 = 5,185 mm/min (203.4 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (3 × 0.5 × 5185) / 1000 = 7.78 cm³/min (0.47 in³/min)
Specific Cutting Force (kc) for HDPE (High-Density Polyethylene): 180 N/mm². Spindle drive efficiency η = 0.80.

HDPE (High-Density Polyethylene) (2 mm) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 2 mm
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 2 mm 1 mm 1× 1,690 65.9 3.38 0.01
Slotting (100% WOC) 3F 2 mm 1 mm 1× 2,535 98.8 5.07 0.02
Slotting (100% WOC) 4F 2 mm 1 mm 1× 3,380 131.8 6.76 0.03
Profiling / HEM (25% WOC) 2F 0.5 mm 3 mm 1.1547× 2,593 101.7 3.89 0.01
Profiling / HEM (25% WOC) 3F 0.5 mm 3 mm 1.1547× 3,889 152.6 5.83 0.02
Profiling / HEM (25% WOC) CURRENT 4F 0.5 mm 3 mm 1.1547× 5,185 203.4 7.78 0.03
Adaptive Clearing (10% WOC) 2F 0.2 mm 4 mm 1.6667× 3,753 147.5 3 0.01
Adaptive Clearing (10% WOC) 3F 0.2 mm 4 mm 1.6667× 5,629 221.3 4.5 0.02
Adaptive Clearing (10% WOC) 4F 0.2 mm 4 mm 1.6667× 7,506 295.1 6 0.02

Shop-Floor Machining Strategy for HDPE (High-Density Polyethylene)

Work Hardening: None (Significant thermal expansion coefficient: 10x of steel)
Coolant & Lubrication Protocol

Cold Compressed Air Blast or Water Mist

Pressure: 5 bar compressed air

HDPE melts at only 130°C (266°F). Cold air blast is mandatory to prevent gumming.

Chip Evacuation & Tool Path Guidance

Chip Flow: Produces fluffy, lightweight, static-charged continuous shavings. High volume vacuum extraction recommended.

Milling Direction: Climb milling prevents feathered edge tears.

Expert Machinist Tips:
  • Use razor-sharp single flute O-flute cutters with polished gullets.
  • Account for thermal contraction: warm parts measured straight off the CNC machine will shrink when cooled to 20°C room temp.
  • Do not allow tool to dwell or friction will melt a pocket into the plastic.

Frequently Asked CNC Questions (HDPE (High-Density Polyethylene) / 2 mm)

What is the recommended RPM for milling HDPE (High-Density Polyethylene) with a 2 mm end mill?
For a 2 mm (2 mm) TiAlN coated carbide end mill in HDPE (High-Density Polyethylene), the baseline surface cutting speed is 450 m/min (1476.4 SFM), which translates to a calculated spindle speed of 71,620 RPM. If using uncoated carbide, reduce surface speed to 400 m/min (1300 SFM / 63662 RPM). For HSS cutters, speed must be restricted to 120 m/min (19099 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 2 mm in HDPE (High-Density Polyethylene)?
At 71,620 RPM with a 4-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0181 mm/tooth (0.00071"/tooth) after applying a radial chip thinning factor (CTF) of 1.1547×. This yields a table feed rate of 5185 mm/min (203.4 IPM). Ramping or plunging into material should be limited to 35% of table feed (1815 mm/min / 71.2 IPM) at an entry ramp angle of 1.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 0.5 mm), the Chip Thinning Factor is 1.1547×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining HDPE (High-Density Polyethylene)?
Cold Compressed Air Blast or Water Mist. Pressure specification: 5 bar compressed air. Engineering rationale: HDPE melts at only 130°C (266°F). Cold air blast is mandatory to prevent gumming.