Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

HDPE (High-Density Polyethylene) — 3 mm 3-Flute Speeds & Feeds

ISO Group O 68 Shore D / 65 Rockwell R

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
47,746 RPM
Surface Speed: 450 m/min (1476.4 SFM)
Table Feed Rate F = RPM·z·fz
3,595 mm/min
141.8 IPM
Plunge/Ramp Rate: 1258 mm/min
Adjusted Chip Load CTF: 1.1547×
0.0251 mm/t
0.00099 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
12.13 cm³/min
0.74 in³/min
Power Required: 0.05 kW (0.06 HP)
Direct CNC Machining Solution

For milling HDPE (High-Density Polyethylene) with a 3 mm 3-flute TiAlN carbide end mill, the recommended spindle speed is 47,746 RPM at 450 m/min (1476.4 SFM), with a profiling feed rate of 3,595 mm/min (141.8 IPM) and adjusted chip load of 0.0251 mm/tooth, achieving a material removal rate of 12.13 cm³/min (0.74 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
HDPE (High-Density Polyethylene) Stock CLIMB D = 3 mm (0.1181") ae = 0.75 mm ap = 4.5 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1547×
Spindle Torque 0.01 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (450 × 1000) / (π × 3) = 47,746 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 0.75/3 = 0.25 → CTF = 1.1547×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0217 mm × 1.1547 = 0.0251 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 47,746 × 3 × 0.0251 = 3,595 mm/min (141.8 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (4.5 × 0.75 × 3595) / 1000 = 12.13 cm³/min (0.74 in³/min)
Specific Cutting Force (kc) for HDPE (High-Density Polyethylene): 180 N/mm². Spindle drive efficiency η = 0.80.

HDPE (High-Density Polyethylene) (3 mm) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 3 mm
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 3 mm 1.5 mm 1× 1,557 61.1 7.01 0.03
Slotting (100% WOC) 3F 3 mm 1.5 mm 1× 2,335 91.7 10.51 0.04
Slotting (100% WOC) 4F 3 mm 1.5 mm 1× 3,113 122.2 14.01 0.05
Profiling / HEM (25% WOC) 2F 0.75 mm 4.5 mm 1.1547× 2,397 94.5 8.09 0.03
Profiling / HEM (25% WOC) CURRENT 3F 0.75 mm 4.5 mm 1.1547× 3,595 141.8 12.13 0.05
Profiling / HEM (25% WOC) 4F 0.75 mm 4.5 mm 1.1547× 4,794 189.1 16.18 0.06
Adaptive Clearing (10% WOC) 2F 0.3 mm 6 mm 1.6667× 3,457 136.6 6.22 0.02
Adaptive Clearing (10% WOC) 3F 0.3 mm 6 mm 1.6667× 5,185 204.8 9.33 0.03
Adaptive Clearing (10% WOC) 4F 0.3 mm 6 mm 1.6667× 6,914 273.1 12.45 0.05

Shop-Floor Machining Strategy for HDPE (High-Density Polyethylene)

Work Hardening: None (Significant thermal expansion coefficient: 10x of steel)
Coolant & Lubrication Protocol

Cold Compressed Air Blast or Water Mist

Pressure: 5 bar compressed air

HDPE melts at only 130°C (266°F). Cold air blast is mandatory to prevent gumming.

Chip Evacuation & Tool Path Guidance

Chip Flow: Produces fluffy, lightweight, static-charged continuous shavings. High volume vacuum extraction recommended.

Milling Direction: Climb milling prevents feathered edge tears.

Expert Machinist Tips:
  • Use razor-sharp single flute O-flute cutters with polished gullets.
  • Account for thermal contraction: warm parts measured straight off the CNC machine will shrink when cooled to 20°C room temp.
  • Do not allow tool to dwell or friction will melt a pocket into the plastic.

Frequently Asked CNC Questions (HDPE (High-Density Polyethylene) / 3 mm)

What is the recommended RPM for milling HDPE (High-Density Polyethylene) with a 3 mm end mill?
For a 3 mm (3 mm) TiAlN coated carbide end mill in HDPE (High-Density Polyethylene), the baseline surface cutting speed is 450 m/min (1476.4 SFM), which translates to a calculated spindle speed of 47,746 RPM. If using uncoated carbide, reduce surface speed to 400 m/min (1300 SFM / 42441 RPM). For HSS cutters, speed must be restricted to 120 m/min (12732 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 3 mm in HDPE (High-Density Polyethylene)?
At 47,746 RPM with a 3-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0251 mm/tooth (0.00099"/tooth) after applying a radial chip thinning factor (CTF) of 1.1547×. This yields a table feed rate of 3595 mm/min (141.8 IPM). Ramping or plunging into material should be limited to 35% of table feed (1258 mm/min / 49.6 IPM) at an entry ramp angle of 2.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 0.75 mm), the Chip Thinning Factor is 1.1547×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining HDPE (High-Density Polyethylene)?
Cold Compressed Air Blast or Water Mist. Pressure specification: 5 bar compressed air. Engineering rationale: HDPE melts at only 130°C (266°F). Cold air blast is mandatory to prevent gumming.