HDPE (High-Density Polyethylene) — 4 mm 3-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling HDPE (High-Density Polyethylene) with a 4 mm 3-flute TiAlN carbide end mill, the recommended spindle speed is 35,810 RPM at 450 m/min (1476.4 SFM), with a profiling feed rate of 3,384 mm/min (133.2 IPM) and adjusted chip load of 0.0315 mm/tooth, achieving a material removal rate of 20.3 cm³/min (1.24 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathHDPE (High-Density Polyethylene) (4 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 4 mm | 2 mm | 1× | 1,468 | 58 | 11.74 | 0.04 |
| Slotting (100% WOC) | 3F | 4 mm | 2 mm | 1× | 2,202 | 87 | 17.62 | 0.07 |
| Slotting (100% WOC) | 4F | 4 mm | 2 mm | 1× | 2,936 | 116 | 23.49 | 0.09 |
| Profiling / HEM (25% WOC) | 2F | 1 mm | 6 mm | 1.1547× | 2,256 | 88.8 | 13.54 | 0.05 |
| Profiling / HEM (25% WOC) CURRENT | 3F | 1 mm | 6 mm | 1.1547× | 3,384 | 133.2 | 20.3 | 0.08 |
| Profiling / HEM (25% WOC) | 4F | 1 mm | 6 mm | 1.1547× | 4,512 | 177.6 | 27.07 | 0.1 |
| Adaptive Clearing (10% WOC) | 2F | 0.4 mm | 8 mm | 1.6667× | 3,259 | 128.2 | 10.43 | 0.04 |
| Adaptive Clearing (10% WOC) | 3F | 0.4 mm | 8 mm | 1.6667× | 4,888 | 192.3 | 15.64 | 0.06 |
| Adaptive Clearing (10% WOC) | 4F | 0.4 mm | 8 mm | 1.6667× | 6,517 | 256.4 | 20.85 | 0.08 |
Shop-Floor Machining Strategy for HDPE (High-Density Polyethylene)
Work Hardening: None (Significant thermal expansion coefficient: 10x of steel)Cold Compressed Air Blast or Water Mist
Pressure: 5 bar compressed air
HDPE melts at only 130°C (266°F). Cold air blast is mandatory to prevent gumming.
Chip Flow: Produces fluffy, lightweight, static-charged continuous shavings. High volume vacuum extraction recommended.
Milling Direction: Climb milling prevents feathered edge tears.
- Use razor-sharp single flute O-flute cutters with polished gullets.
- Account for thermal contraction: warm parts measured straight off the CNC machine will shrink when cooled to 20°C room temp.
- Do not allow tool to dwell or friction will melt a pocket into the plastic.
Frequently Asked CNC Questions (HDPE (High-Density Polyethylene) / 4 mm)
What is the recommended RPM for milling HDPE (High-Density Polyethylene) with a 4 mm end mill?
What table feed rate and chip load should I program for 4 mm in HDPE (High-Density Polyethylene)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining HDPE (High-Density Polyethylene)?
Recent Calculations
No recent calculations saved yet.