Polycarbonate (Lexan / PC Thermoplastic) — 1/2" (0.500 in) 2-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling Polycarbonate (Lexan / PC Thermoplastic) with a 1/2" (0.500 in) 2-flute TiAlN carbide end mill, the recommended spindle speed is 9,524 RPM at 380 m/min (1246.7 SFM), with a profiling feed rate of 1,261 mm/min (49.7 IPM) and adjusted chip load of 0.0662 mm/tooth, achieving a material removal rate of 76.15 cm³/min (4.65 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathPolycarbonate (Lexan / PC Thermoplastic) (1/2" (0.500 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 12.7 mm | 6.35 mm | 1× | 819 | 32.2 | 66.05 | 0.41 |
| Slotting (100% WOC) | 3F | 12.7 mm | 6.35 mm | 1× | 1,229 | 48.3 | 99.11 | 0.62 |
| Slotting (100% WOC) | 4F | 12.7 mm | 6.35 mm | 1× | 1,638 | 64.4 | 132.1 | 0.83 |
| Profiling / HEM (25% WOC) CURRENT | 2F | 3.17 mm | 19.05 mm | 1.1553× | 1,261 | 49.7 | 76.15 | 0.48 |
| Profiling / HEM (25% WOC) | 3F | 3.17 mm | 19.05 mm | 1.1553× | 1,891 | 74.6 | 114.19 | 0.71 |
| Profiling / HEM (25% WOC) | 4F | 3.17 mm | 19.05 mm | 1.1553× | 2,522 | 99.4 | 152.3 | 0.95 |
| Adaptive Clearing (10% WOC) | 2F | 1.27 mm | 25.4 mm | 1.6667× | 1,819 | 71.6 | 58.68 | 0.37 |
| Adaptive Clearing (10% WOC) | 3F | 1.27 mm | 25.4 mm | 1.6667× | 2,729 | 107.4 | 88.03 | 0.55 |
| Adaptive Clearing (10% WOC) | 4F | 1.27 mm | 25.4 mm | 1.6667× | 3,638 | 143.2 | 117.35 | 0.73 |
Shop-Floor Machining Strategy for Polycarbonate (Lexan / PC Thermoplastic)
Work Hardening: None (High internal residual stress from extrusion)Cold Air Blast Only or Pure Deionized Water
Pressure: Cold air gun at 5 bar
CRITICAL: Never expose polycarbonate to petroleum, synthetic cutting oils, or chemical solvents. Chemical exposure induces immediate catastrophic stress crazing and micro-fractures.
Chip Flow: Clean crisp plastic chips; air blast prevents chip recutting on optical surfaces.
Milling Direction: Climb milling mandatory to avoid chipping edge breakout.
- Maintain sharp high-rake tools; dull tools induce severe internal residual stress that causes delayed part cracking.
- Anneal machined parts at 120°C (250°F) for 2 hours if maximum impact strength is required.
- Use protective masking film on sheet surfaces to prevent surface scratches from chip wash.
Frequently Asked CNC Questions (Polycarbonate (Lexan / PC Thermoplastic) / 1/2" (0.500 in))
What is the recommended RPM for milling Polycarbonate (Lexan / PC Thermoplastic) with a 1/2" (0.500 in) end mill?
What table feed rate and chip load should I program for 1/2" (0.500 in) in Polycarbonate (Lexan / PC Thermoplastic)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining Polycarbonate (Lexan / PC Thermoplastic)?
Recent Calculations
No recent calculations saved yet.