Polycarbonate (Lexan / PC Thermoplastic) — 1" (1.000 in) 4-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling Polycarbonate (Lexan / PC Thermoplastic) with a 1" (1.000 in) 4-flute TiAlN carbide end mill, the recommended spindle speed is 4,762 RPM at 380 m/min (1246.7 SFM), with a profiling feed rate of 2,194 mm/min (86.5 IPM) and adjusted chip load of 0.1152 mm/tooth, achieving a material removal rate of 530.81 cm³/min (32.44 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathPolycarbonate (Lexan / PC Thermoplastic) (1" (1.000 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 25.4 mm | 12.7 mm | 1× | 712 | 28 | 229.68 | 1.44 |
| Slotting (100% WOC) | 3F | 25.4 mm | 12.7 mm | 1× | 1,069 | 42 | 344.84 | 2.16 |
| Slotting (100% WOC) | 4F | 25.4 mm | 12.7 mm | 1× | 1,425 | 56 | 459.68 | 2.87 |
| Profiling / HEM (25% WOC) | 2F | 6.35 mm | 38.1 mm | 1.1547× | 1,097 | 43.2 | 265.4 | 1.66 |
| Profiling / HEM (25% WOC) | 3F | 6.35 mm | 38.1 mm | 1.1547× | 1,646 | 64.9 | 398.23 | 2.49 |
| Profiling / HEM (25% WOC) CURRENT | 4F | 6.35 mm | 38.1 mm | 1.1547× | 2,194 | 86.5 | 530.81 | 3.32 |
| Adaptive Clearing (10% WOC) | 2F | 2.54 mm | 50.8 mm | 1.6667× | 1,584 | 62.4 | 204.39 | 1.28 |
| Adaptive Clearing (10% WOC) | 3F | 2.54 mm | 50.8 mm | 1.6667× | 2,376 | 93.6 | 306.58 | 1.92 |
| Adaptive Clearing (10% WOC) | 4F | 2.54 mm | 50.8 mm | 1.6667× | 3,168 | 124.8 | 408.77 | 2.55 |
Shop-Floor Machining Strategy for Polycarbonate (Lexan / PC Thermoplastic)
Work Hardening: None (High internal residual stress from extrusion)Cold Air Blast Only or Pure Deionized Water
Pressure: Cold air gun at 5 bar
CRITICAL: Never expose polycarbonate to petroleum, synthetic cutting oils, or chemical solvents. Chemical exposure induces immediate catastrophic stress crazing and micro-fractures.
Chip Flow: Clean crisp plastic chips; air blast prevents chip recutting on optical surfaces.
Milling Direction: Climb milling mandatory to avoid chipping edge breakout.
- Maintain sharp high-rake tools; dull tools induce severe internal residual stress that causes delayed part cracking.
- Anneal machined parts at 120°C (250°F) for 2 hours if maximum impact strength is required.
- Use protective masking film on sheet surfaces to prevent surface scratches from chip wash.
Frequently Asked CNC Questions (Polycarbonate (Lexan / PC Thermoplastic) / 1" (1.000 in))
What is the recommended RPM for milling Polycarbonate (Lexan / PC Thermoplastic) with a 1" (1.000 in) end mill?
What table feed rate and chip load should I program for 1" (1.000 in) in Polycarbonate (Lexan / PC Thermoplastic)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining Polycarbonate (Lexan / PC Thermoplastic)?
Recent Calculations
No recent calculations saved yet.