Polycarbonate (Lexan / PC Thermoplastic) — 16 mm 3-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling Polycarbonate (Lexan / PC Thermoplastic) with a 16 mm 3-flute TiAlN carbide end mill, the recommended spindle speed is 7,560 RPM at 380 m/min (1246.7 SFM), with a profiling feed rate of 1,805 mm/min (71 IPM) and adjusted chip load of 0.0796 mm/tooth, achieving a material removal rate of 173.28 cm³/min (10.57 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathPolycarbonate (Lexan / PC Thermoplastic) (16 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 16 mm | 8 mm | 1× | 782 | 30.8 | 100.1 | 0.63 |
| Slotting (100% WOC) | 3F | 16 mm | 8 mm | 1× | 1,173 | 46.3 | 150.14 | 0.94 |
| Slotting (100% WOC) | 4F | 16 mm | 8 mm | 1× | 1,563 | 61.7 | 200.06 | 1.25 |
| Profiling / HEM (25% WOC) | 2F | 4 mm | 24 mm | 1.1547× | 1,204 | 47.3 | 115.58 | 0.72 |
| Profiling / HEM (25% WOC) CURRENT | 3F | 4 mm | 24 mm | 1.1547× | 1,805 | 71 | 173.28 | 1.08 |
| Profiling / HEM (25% WOC) | 4F | 4 mm | 24 mm | 1.1547× | 2,407 | 94.7 | 231.07 | 1.44 |
| Adaptive Clearing (10% WOC) | 2F | 1.6 mm | 32 mm | 1.6667× | 1,736 | 68.3 | 88.88 | 0.56 |
| Adaptive Clearing (10% WOC) | 3F | 1.6 mm | 32 mm | 1.6667× | 2,604 | 102.5 | 133.32 | 0.83 |
| Adaptive Clearing (10% WOC) | 4F | 1.6 mm | 32 mm | 1.6667× | 3,472 | 136.7 | 177.77 | 1.11 |
Shop-Floor Machining Strategy for Polycarbonate (Lexan / PC Thermoplastic)
Work Hardening: None (High internal residual stress from extrusion)Cold Air Blast Only or Pure Deionized Water
Pressure: Cold air gun at 5 bar
CRITICAL: Never expose polycarbonate to petroleum, synthetic cutting oils, or chemical solvents. Chemical exposure induces immediate catastrophic stress crazing and micro-fractures.
Chip Flow: Clean crisp plastic chips; air blast prevents chip recutting on optical surfaces.
Milling Direction: Climb milling mandatory to avoid chipping edge breakout.
- Maintain sharp high-rake tools; dull tools induce severe internal residual stress that causes delayed part cracking.
- Anneal machined parts at 120°C (250°F) for 2 hours if maximum impact strength is required.
- Use protective masking film on sheet surfaces to prevent surface scratches from chip wash.
Frequently Asked CNC Questions (Polycarbonate (Lexan / PC Thermoplastic) / 16 mm)
What is the recommended RPM for milling Polycarbonate (Lexan / PC Thermoplastic) with a 16 mm end mill?
What table feed rate and chip load should I program for 16 mm in Polycarbonate (Lexan / PC Thermoplastic)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining Polycarbonate (Lexan / PC Thermoplastic)?
Recent Calculations
No recent calculations saved yet.