Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

Polycarbonate (Lexan / PC Thermoplastic) — 5/8" (0.625 in) 4-Flute Speeds & Feeds

ISO Group O 70 Shore D / 118 Rockwell R

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
7,619 RPM
Surface Speed: 380 m/min (1246.7 SFM)
Table Feed Rate F = RPM·z·fz
2,411 mm/min
94.8 IPM
Plunge/Ramp Rate: 844 mm/min
Adjusted Chip Load CTF: 1.1546×
0.0791 mm/t
0.00311 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
227.9 cm³/min
13.89 in³/min
Power Required: 1.42 kW (1.91 HP)
Direct CNC Machining Solution

For milling Polycarbonate (Lexan / PC Thermoplastic) with a 5/8" (0.625 in) 4-flute TiAlN carbide end mill, the recommended spindle speed is 7,619 RPM at 380 m/min (1246.7 SFM), with a profiling feed rate of 2,411 mm/min (94.8 IPM) and adjusted chip load of 0.0791 mm/tooth, achieving a material removal rate of 227.9 cm³/min (13.89 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
Polycarbonate (Lexan / PC Thermoplastic) Stock CLIMB D = 15.875 mm (0.625") ae = 3.97 mm ap = 23.81 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1546×
Spindle Torque 1.43 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (380 × 1000) / (π × 15.875) = 7,619 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 3.97/15.875 = 0.25 → CTF = 1.1546×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0685 mm × 1.1546 = 0.0791 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 7,619 × 4 × 0.0791 = 2,411 mm/min (94.8 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (23.81 × 3.97 × 2411) / 1000 = 227.9 cm³/min (13.89 in³/min)
Specific Cutting Force (kc) for Polycarbonate (Lexan / PC Thermoplastic): 300 N/mm². Spindle drive efficiency η = 0.80.

Polycarbonate (Lexan / PC Thermoplastic) (5/8" (0.625 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 5/8" (0.625 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 15.88 mm 7.94 mm 1× 783 30.8 98.73 0.62
Slotting (100% WOC) 3F 15.88 mm 7.94 mm 1× 1,175 46.2 148.15 0.93
Slotting (100% WOC) 4F 15.88 mm 7.94 mm 1× 1,566 61.6 197.45 1.23
Profiling / HEM (25% WOC) 2F 3.97 mm 23.81 mm 1.1546× 1,205 47.4 113.9 0.71
Profiling / HEM (25% WOC) 3F 3.97 mm 23.81 mm 1.1546× 1,808 71.1 170.9 1.07
Profiling / HEM (25% WOC) CURRENT 4F 3.97 mm 23.81 mm 1.1546× 2,411 94.8 227.9 1.42
Adaptive Clearing (10% WOC) 2F 1.59 mm 31.75 mm 1.6655× 1,739 68.4 87.79 0.55
Adaptive Clearing (10% WOC) 3F 1.59 mm 31.75 mm 1.6655× 2,608 102.6 131.66 0.82
Adaptive Clearing (10% WOC) 4F 1.59 mm 31.75 mm 1.6655× 3,477 136.8 175.53 1.1

Shop-Floor Machining Strategy for Polycarbonate (Lexan / PC Thermoplastic)

Work Hardening: None (High internal residual stress from extrusion)
Coolant & Lubrication Protocol

Cold Air Blast Only or Pure Deionized Water

Pressure: Cold air gun at 5 bar

CRITICAL: Never expose polycarbonate to petroleum, synthetic cutting oils, or chemical solvents. Chemical exposure induces immediate catastrophic stress crazing and micro-fractures.

Chip Evacuation & Tool Path Guidance

Chip Flow: Clean crisp plastic chips; air blast prevents chip recutting on optical surfaces.

Milling Direction: Climb milling mandatory to avoid chipping edge breakout.

Expert Machinist Tips:
  • Maintain sharp high-rake tools; dull tools induce severe internal residual stress that causes delayed part cracking.
  • Anneal machined parts at 120°C (250°F) for 2 hours if maximum impact strength is required.
  • Use protective masking film on sheet surfaces to prevent surface scratches from chip wash.

Frequently Asked CNC Questions (Polycarbonate (Lexan / PC Thermoplastic) / 5/8" (0.625 in))

What is the recommended RPM for milling Polycarbonate (Lexan / PC Thermoplastic) with a 5/8" (0.625 in) end mill?
For a 5/8" (0.625 in) (15.875 mm) TiAlN coated carbide end mill in Polycarbonate (Lexan / PC Thermoplastic), the baseline surface cutting speed is 380 m/min (1246.7 SFM), which translates to a calculated spindle speed of 7,619 RPM. If using uncoated carbide, reduce surface speed to 320 m/min (1050 SFM / 6416 RPM). For HSS cutters, speed must be restricted to 100 m/min (2005 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 5/8" (0.625 in) in Polycarbonate (Lexan / PC Thermoplastic)?
At 7,619 RPM with a 4-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0791 mm/tooth (0.00311"/tooth) after applying a radial chip thinning factor (CTF) of 1.1546×. This yields a table feed rate of 2411 mm/min (94.8 IPM). Ramping or plunging into material should be limited to 35% of table feed (844 mm/min / 33.2 IPM) at an entry ramp angle of 1.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 3.97 mm), the Chip Thinning Factor is 1.1546×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining Polycarbonate (Lexan / PC Thermoplastic)?
Cold Air Blast Only or Pure Deionized Water. Pressure specification: Cold air gun at 5 bar. Engineering rationale: CRITICAL: Never expose polycarbonate to petroleum, synthetic cutting oils, or chemical solvents. Chemical exposure induces immediate catastrophic stress crazing and micro-fractures.