Polycarbonate (Lexan / PC Thermoplastic) — 8 mm 4-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling Polycarbonate (Lexan / PC Thermoplastic) with a 8 mm 4-flute TiAlN carbide end mill, the recommended spindle speed is 15,120 RPM at 380 m/min (1246.7 SFM), with a profiling feed rate of 2,764 mm/min (108.9 IPM) and adjusted chip load of 0.0457 mm/tooth, achieving a material removal rate of 66.34 cm³/min (4.05 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathPolycarbonate (Lexan / PC Thermoplastic) (8 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 8 mm | 4 mm | 1× | 898 | 35.4 | 28.74 | 0.18 |
| Slotting (100% WOC) | 3F | 8 mm | 4 mm | 1× | 1,347 | 53.1 | 43.1 | 0.27 |
| Slotting (100% WOC) | 4F | 8 mm | 4 mm | 1× | 1,796 | 70.8 | 57.47 | 0.36 |
| Profiling / HEM (25% WOC) | 2F | 2 mm | 12 mm | 1.1547× | 1,382 | 54.4 | 33.17 | 0.21 |
| Profiling / HEM (25% WOC) | 3F | 2 mm | 12 mm | 1.1547× | 2,073 | 81.6 | 49.75 | 0.31 |
| Profiling / HEM (25% WOC) CURRENT | 4F | 2 mm | 12 mm | 1.1547× | 2,764 | 108.9 | 66.34 | 0.41 |
| Adaptive Clearing (10% WOC) | 2F | 0.8 mm | 16 mm | 1.6667× | 1,996 | 78.6 | 25.55 | 0.16 |
| Adaptive Clearing (10% WOC) | 3F | 0.8 mm | 16 mm | 1.6667× | 2,994 | 117.9 | 38.32 | 0.24 |
| Adaptive Clearing (10% WOC) | 4F | 0.8 mm | 16 mm | 1.6667× | 3,992 | 157.2 | 51.1 | 0.32 |
Shop-Floor Machining Strategy for Polycarbonate (Lexan / PC Thermoplastic)
Work Hardening: None (High internal residual stress from extrusion)Cold Air Blast Only or Pure Deionized Water
Pressure: Cold air gun at 5 bar
CRITICAL: Never expose polycarbonate to petroleum, synthetic cutting oils, or chemical solvents. Chemical exposure induces immediate catastrophic stress crazing and micro-fractures.
Chip Flow: Clean crisp plastic chips; air blast prevents chip recutting on optical surfaces.
Milling Direction: Climb milling mandatory to avoid chipping edge breakout.
- Maintain sharp high-rake tools; dull tools induce severe internal residual stress that causes delayed part cracking.
- Anneal machined parts at 120°C (250°F) for 2 hours if maximum impact strength is required.
- Use protective masking film on sheet surfaces to prevent surface scratches from chip wash.
Frequently Asked CNC Questions (Polycarbonate (Lexan / PC Thermoplastic) / 8 mm)
What is the recommended RPM for milling Polycarbonate (Lexan / PC Thermoplastic) with a 8 mm end mill?
What table feed rate and chip load should I program for 8 mm in Polycarbonate (Lexan / PC Thermoplastic)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining Polycarbonate (Lexan / PC Thermoplastic)?
Recent Calculations
No recent calculations saved yet.