Polycarbonate (Lexan / PC Thermoplastic) — 6 mm 4-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling Polycarbonate (Lexan / PC Thermoplastic) with a 6 mm 4-flute TiAlN carbide end mill, the recommended spindle speed is 20,160 RPM at 380 m/min (1246.7 SFM), with a profiling feed rate of 2,927 mm/min (115.3 IPM) and adjusted chip load of 0.0363 mm/tooth, achieving a material removal rate of 39.51 cm³/min (2.41 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathPolycarbonate (Lexan / PC Thermoplastic) (6 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 6 mm | 3 mm | 1× | 952 | 37.5 | 17.14 | 0.11 |
| Slotting (100% WOC) | 3F | 6 mm | 3 mm | 1× | 1,427 | 56.2 | 25.69 | 0.16 |
| Slotting (100% WOC) | 4F | 6 mm | 3 mm | 1× | 1,903 | 75 | 34.25 | 0.21 |
| Profiling / HEM (25% WOC) | 2F | 1.5 mm | 9 mm | 1.1547× | 1,464 | 57.7 | 19.76 | 0.12 |
| Profiling / HEM (25% WOC) | 3F | 1.5 mm | 9 mm | 1.1547× | 2,195 | 86.5 | 29.63 | 0.19 |
| Profiling / HEM (25% WOC) CURRENT | 4F | 1.5 mm | 9 mm | 1.1547× | 2,927 | 115.3 | 39.51 | 0.25 |
| Adaptive Clearing (10% WOC) | 2F | 0.6 mm | 12 mm | 1.6667× | 2,109 | 83.1 | 15.18 | 0.09 |
| Adaptive Clearing (10% WOC) | 3F | 0.6 mm | 12 mm | 1.6667× | 3,163 | 124.6 | 22.77 | 0.14 |
| Adaptive Clearing (10% WOC) | 4F | 0.6 mm | 12 mm | 1.6667× | 4,217 | 166.1 | 30.36 | 0.19 |
Shop-Floor Machining Strategy for Polycarbonate (Lexan / PC Thermoplastic)
Work Hardening: None (High internal residual stress from extrusion)Cold Air Blast Only or Pure Deionized Water
Pressure: Cold air gun at 5 bar
CRITICAL: Never expose polycarbonate to petroleum, synthetic cutting oils, or chemical solvents. Chemical exposure induces immediate catastrophic stress crazing and micro-fractures.
Chip Flow: Clean crisp plastic chips; air blast prevents chip recutting on optical surfaces.
Milling Direction: Climb milling mandatory to avoid chipping edge breakout.
- Maintain sharp high-rake tools; dull tools induce severe internal residual stress that causes delayed part cracking.
- Anneal machined parts at 120°C (250°F) for 2 hours if maximum impact strength is required.
- Use protective masking film on sheet surfaces to prevent surface scratches from chip wash.
Frequently Asked CNC Questions (Polycarbonate (Lexan / PC Thermoplastic) / 6 mm)
What is the recommended RPM for milling Polycarbonate (Lexan / PC Thermoplastic) with a 6 mm end mill?
What table feed rate and chip load should I program for 6 mm in Polycarbonate (Lexan / PC Thermoplastic)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining Polycarbonate (Lexan / PC Thermoplastic)?
Recent Calculations
No recent calculations saved yet.