Ti-6Al-4V Titanium Alloy (Grade 5) — 2 mm 2-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling Ti-6Al-4V Titanium Alloy (Grade 5) with a 2 mm 2-flute TiAlN carbide end mill, the recommended spindle speed is 10,345 RPM at 65 m/min (213.3 SFM), with a profiling feed rate of 134 mm/min (5.4 IPM) and adjusted chip load of 0.0065 mm/tooth, achieving a material removal rate of 0.2 cm³/min (0.01 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathTi-6Al-4V Titanium Alloy (Grade 5) (2 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 2 mm | 1 mm | 1× | 87 | 3.5 | 0.17 | 0.01 |
| Slotting (100% WOC) | 3F | 2 mm | 1 mm | 1× | 130 | 5.3 | 0.26 | 0.02 |
| Slotting (100% WOC) | 4F | 2 mm | 1 mm | 1× | 174 | 7 | 0.35 | 0.02 |
| Profiling / HEM (25% WOC) CURRENT | 2F | 0.5 mm | 3 mm | 1.1547× | 134 | 5.4 | 0.2 | 0.01 |
| Profiling / HEM (25% WOC) | 3F | 0.5 mm | 3 mm | 1.1547× | 202 | 8.1 | 0.3 | 0.02 |
| Profiling / HEM (25% WOC) | 4F | 0.5 mm | 3 mm | 1.1547× | 269 | 10.8 | 0.4 | 0.02 |
| Adaptive Clearing (10% WOC) | 2F | 0.2 mm | 4 mm | 1.6667× | 192 | 7.7 | 0.15 | 0.01 |
| Adaptive Clearing (10% WOC) | 3F | 0.2 mm | 4 mm | 1.6667× | 289 | 11.5 | 0.23 | 0.01 |
| Adaptive Clearing (10% WOC) | 4F | 0.2 mm | 4 mm | 1.6667× | 385 | 15.3 | 0.31 | 0.02 |
Shop-Floor Machining Strategy for Ti-6Al-4V Titanium Alloy (Grade 5)
Work Hardening: HighHigh-Pressure Through-Spindle Flood Coolant (70 bar / 1000 PSI)
Pressure: 70 bar through-spindle coolant mandatory for deep milling
Titanium thermal conductivity is 1/6th of steel; heat cannot dissipate into chips and concentrates directly on the cutting edge. WARNING: Dry titanium chips present a combustible metal fire hazard.
Chip Flow: Chips weld chemically to tool steel and carbide at elevated temperatures.
Milling Direction: Strict climb milling. Keep radial engagement (ae) under 20% of tool diameter.
- LOW SPEED, HIGH FEED, ABUNDANT COOLANT: The universal titanium triad.
- Arc into cuts using a roll-in programmed entry; linear plunges cause tool shock fractures.
- Never dwell in the cut; program corner deceleration cautiously to prevent tool rubbing.
Frequently Asked CNC Questions (Ti-6Al-4V Titanium Alloy (Grade 5) / 2 mm)
What is the recommended RPM for milling Ti-6Al-4V Titanium Alloy (Grade 5) with a 2 mm end mill?
What table feed rate and chip load should I program for 2 mm in Ti-6Al-4V Titanium Alloy (Grade 5)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining Ti-6Al-4V Titanium Alloy (Grade 5)?
Recent Calculations
No recent calculations saved yet.