Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

3/8"-24 UNF Grade 8 Torque & Tap Drill Spec

SAE J429 / ASTM A354 Grade BD

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
66.984 N·m
49.405 ft-lbs | 592.86 in-lbs | 6.8305 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
35.162 kN
7,904.8 lbf
Target tension across joint interface
75% Tap Drill d - P
8.433 mm
Q (0.3320 in) (95.3% Eng.)
50% Hard Metal Drill: 8.951 mm
Direct Engineering Specification Summary

The recommended tightening torque for a 3/8"-24 UNF Grade 8 bolt is 66.984 N·m (49.405 ft-lbs) when dry (K=0.20) and 50.238 N·m (37.054 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 35.162 kN (7,904.8 lbf) at 75% proof load. Standard 75% tap drill is Q (0.3320 in).

Thread & Hole Blueprint Visualizer

ASME B1.1 Unified Inch Screw Threads (60° UN)
d = 9.525 mm (0.375") P = 1.05833 mm 3/8"-24 UNF Close: 9.804mm Normal: 10.084mm Loose: 10.719mm
Stress Area (As) 56.663 mm²
Pitch Diameter (d2) 8.838 mm
Minor Diameter (d1) 8.379 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (9.525 − 0.9382 × 1.05833)² = 56.663 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 56.663 mm² × 827.4 N/mm² = 46883 N (46.883 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 46883 N = 35162 N (35.162 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 9.525 mm × 35162 N) / 1000 = 66.984 N·m (49.405 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

3/8"-24 UNF Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: 3/8"-24 UNF
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Grade 5 47.449 Nm
34.997 ft-lb
42.704 Nm
31.497 ft-lb
35.587 Nm
26.247 ft-lb
28.469 Nm
20.998 ft-lb
24.908 33.21
Grade 8 CURRENT 66.984 Nm
49.405 ft-lb
60.286 Nm
44.464 ft-lb
50.238 Nm
37.054 ft-lb
40.19 Nm
29.643 ft-lb
35.162 46.883
18-8 Stainless 25.121 Nm
18.528 ft-lb
22.609 Nm
16.675 ft-lb
18.841 Nm
13.896 ft-lb
15.073 Nm
11.117 ft-lb
13.187 17.583

Frequently Asked Engineering Questions (3/8"-24 UNF Grade 8)

What is the recommended tightening torque for a 3/8"-24 UNF Grade 8 bolt?
For a 3/8"-24 UNF SAE J429 Grade 8 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 66.984 N·m (49.405 ft-lbs / 592.86 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 50.238 N·m (37.054 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 40.19 N·m (29.643 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping 3/8"-24 UNF internal threads?
The standard cut tap drill size for 3/8"-24 UNF is Q (0.3320 in) (0.3320" / 8.433 mm), which delivers approximately 95.3% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 8.951 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a 3/8"-24 UNF Grade 8 fastener develop?
With a tensile stress area (As) of 56.663 mm² (0.08783 in²) and a nominal proof stress of 827.4 MPa (1,20,000 psi), a 3/8"-24 UNF Grade 8 fastener possesses an ultimate proof load of 46.883 kN (10,539.7 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 35.162 kN (7,904.8 lbf) across the joint interface.
What clearance hole diameters should be drilled for 3/8"-24 UNF bolts?
Per ASME B18.2.8 (Clearance Holes for Bolts, Screws, and Studs), recommended clearance hole diameters for a 3/8"-24 UNF fastener are: Close Fit = 9.804 mm (0.386"), Normal Fit = 10.084 mm (0.397"), and Loose Fit = 10.719 mm (0.422"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.