Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

7/16"-14 UNC Grade 5 Torque & Tap Drill Spec

SAE J429 / ASTM A449

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
67.005 N·m
49.421 ft-lbs | 593.05 in-lbs | 6.8327 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
30.149 kN
6,777.7 lbf
Target tension across joint interface
75% Tap Drill d - P
9.347 mm
U (0.3680 in) (89.9% Eng.)
50% Hard Metal Drill: 10.13 mm
Direct Engineering Specification Summary

The recommended tightening torque for a 7/16"-14 UNC Grade 5 bolt is 67.005 N·m (49.421 ft-lbs) when dry (K=0.20) and 50.254 N·m (37.066 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 30.149 kN (6,777.7 lbf) at 75% proof load. Standard 75% tap drill is U (0.3680 in).

Thread & Hole Blueprint Visualizer

ASME B1.1 Unified Inch Screw Threads (60° UN)
d = 11.1125 mm (0.4375") P = 1.81429 mm 7/16"-14 UNC Close: 11.506mm Normal: 11.913mm Loose: 12.7mm
Stress Area (As) 68.586 mm²
Pitch Diameter (d2) 9.934 mm
Minor Diameter (d1) 9.148 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (11.1125 − 0.9382 × 1.81429)² = 68.586 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 68.586 mm² × 586.1 N/mm² = 40198 N (40.198 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 40198 N = 30149 N (30.149 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 11.1125 mm × 30149 N) / 1000 = 67.005 N·m (49.421 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

7/16"-14 UNC Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: 7/16"-14 UNC
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Grade 5 CURRENT 67.005 Nm
49.421 ft-lb
60.305 Nm
44.479 ft-lb
50.254 Nm
37.066 ft-lb
40.203 Nm
29.652 ft-lb
30.149 40.198
Grade 8 94.592 Nm
69.767 ft-lb
85.133 Nm
62.791 ft-lb
70.944 Nm
52.326 ft-lb
56.755 Nm
41.86 ft-lb
42.561 56.748
18-8 Stainless 35.475 Nm
26.165 ft-lb
31.927 Nm
23.548 ft-lb
26.606 Nm
19.624 ft-lb
21.285 Nm
15.699 ft-lb
15.962 21.282

Frequently Asked Engineering Questions (7/16"-14 UNC Grade 5)

What is the recommended tightening torque for a 7/16"-14 UNC Grade 5 bolt?
For a 7/16"-14 UNC SAE J429 Grade 5 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 67.005 N·m (49.421 ft-lbs / 593.05 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 50.254 N·m (37.066 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 40.203 N·m (29.652 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping 7/16"-14 UNC internal threads?
The standard cut tap drill size for 7/16"-14 UNC is U (0.3680 in) (0.3680" / 9.347 mm), which delivers approximately 89.9% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 10.13 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a 7/16"-14 UNC Grade 5 fastener develop?
With a tensile stress area (As) of 68.586 mm² (0.10631 in²) and a nominal proof stress of 586.1 MPa (85,000 psi), a 7/16"-14 UNC Grade 5 fastener possesses an ultimate proof load of 40.198 kN (9,036.9 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 30.149 kN (6,777.7 lbf) across the joint interface.
What clearance hole diameters should be drilled for 7/16"-14 UNC bolts?
Per ASME B18.2.8 (Clearance Holes for Bolts, Screws, and Studs), recommended clearance hole diameters for a 7/16"-14 UNC fastener are: Close Fit = 11.506 mm (0.453"), Normal Fit = 11.913 mm (0.469"), and Loose Fit = 12.7 mm (0.5"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.