Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

7/16"-20 UNF 18-8 Stainless Torque & Tap Drill Spec

ASTM F593 Group 1 / AISI 304

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
39.615 N·m
29.219 ft-lbs | 350.62 in-lbs | 4.0396 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
17.825 kN
4,007.1 lbf
Target tension across joint interface
75% Tap Drill d - P
9.921 mm
25/64" (0.3906 in) (86.6% Eng.)
50% Hard Metal Drill: 10.424 mm
Direct Engineering Specification Summary

The recommended tightening torque for a 7/16"-20 UNF 18-8 Stainless bolt is 39.615 N·m (29.219 ft-lbs) when dry (K=0.20) and 29.711 N·m (21.914 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 17.825 kN (4,007.1 lbf) at 75% proof load. Standard 75% tap drill is 25/64" (0.3906 in).

Thread & Hole Blueprint Visualizer

ASME B1.1 Unified Inch Screw Threads (60° UN)
d = 11.1125 mm (0.4375") P = 1.27 mm 7/16"-20 UNF Close: 11.506mm Normal: 11.913mm Loose: 12.7mm
Stress Area (As) 76.591 mm²
Pitch Diameter (d2) 10.288 mm
Minor Diameter (d1) 9.738 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (11.1125 − 0.9382 × 1.27)² = 76.591 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 76.591 mm² × 310.3 N/mm² = 23766 N (23.766 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 23766 N = 17825 N (17.825 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 11.1125 mm × 17825 N) / 1000 = 39.615 N·m (29.219 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

7/16"-20 UNF Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: 7/16"-20 UNF
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Grade 5 74.826 Nm
55.189 ft-lb
67.343 Nm
49.67 ft-lb
56.119 Nm
41.392 ft-lb
44.896 Nm
33.113 ft-lb
33.667 44.89
Grade 8 105.632 Nm
77.91 ft-lb
95.069 Nm
70.119 ft-lb
79.224 Nm
58.433 ft-lb
63.379 Nm
46.746 ft-lb
47.529 63.371
18-8 Stainless CURRENT 39.615 Nm
29.219 ft-lb
35.654 Nm
26.297 ft-lb
29.711 Nm
21.914 ft-lb
23.769 Nm
17.531 ft-lb
17.825 23.766

Frequently Asked Engineering Questions (7/16"-20 UNF 18-8 Stainless)

What is the recommended tightening torque for a 7/16"-20 UNF 18-8 Stainless bolt?
For a 7/16"-20 UNF 18-8 Stainless Steel (ASTM F593 Group 1) bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 39.615 N·m (29.219 ft-lbs / 350.62 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 29.711 N·m (21.914 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 23.769 N·m (17.531 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping 7/16"-20 UNF internal threads?
The standard cut tap drill size for 7/16"-20 UNF is 25/64" (0.3906 in) (0.3906" / 9.921 mm), which delivers approximately 86.6% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 10.424 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a 7/16"-20 UNF 18-8 Stainless fastener develop?
With a tensile stress area (As) of 76.591 mm² (0.11872 in²) and a nominal proof stress of 310.3 MPa (45,000 psi), a 7/16"-20 UNF 18-8 Stainless fastener possesses an ultimate proof load of 23.766 kN (5,342.9 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 17.825 kN (4,007.1 lbf) across the joint interface.
What clearance hole diameters should be drilled for 7/16"-20 UNF bolts?
Per ASME B18.2.8 (Clearance Holes for Bolts, Screws, and Studs), recommended clearance hole diameters for a 7/16"-20 UNF fastener are: Close Fit = 11.506 mm (0.453"), Normal Fit = 11.913 mm (0.469"), and Loose Fit = 12.7 mm (0.5"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.