Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

M10 x 1.5 Class 10.9 Torque & Tap Drill Spec

ISO 898-1

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
72.196 N·m
53.249 ft-lbs | 638.99 in-lbs | 7.362 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
36.098 kN
8,115.2 lbf
Target tension across joint interface
75% Tap Drill d - P
8.5 mm
8.5 mm (92.4% Eng.)
50% Hard Metal Drill: 9.188 mm
Direct Engineering Specification Summary

The recommended tightening torque for a M10 x 1.5 Class 10.9 bolt is 72.196 N·m (53.249 ft-lbs) when dry (K=0.20) and 54.147 N·m (39.937 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 36.098 kN (8,115.2 lbf) at 75% proof load. Standard 75% tap drill is 8.5 mm.

Thread & Hole Blueprint Visualizer

ISO 261 / ISO 965-1 (Metric 60°)
d = 10 mm (0.3937") P = 1.5 mm M10 x 1.5 Close: 10.5mm Normal: 11mm Loose: 12mm
Stress Area (As) 57.989 mm²
Pitch Diameter (d2) 9.026 mm
Minor Diameter (d1) 8.376 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (10 − 0.9382 × 1.5)² = 57.989 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 57.989 mm² × 830 N/mm² = 48131 N (48.131 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 48131 N = 36098 N (36.098 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 10 mm × 36098 N) / 1000 = 72.196 N·m (53.249 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

M10 x 1.5 Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: M10 x 1.5
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Class 8.8 52.19 Nm
38.493 ft-lb
46.971 Nm
34.644 ft-lb
39.143 Nm
28.87 ft-lb
31.314 Nm
23.096 ft-lb
26.095 34.793
Class 10.9 CURRENT 72.196 Nm
53.249 ft-lb
64.977 Nm
47.924 ft-lb
54.147 Nm
39.937 ft-lb
43.318 Nm
31.95 ft-lb
36.098 48.131
Class 12.9 84.374 Nm
62.231 ft-lb
75.937 Nm
56.008 ft-lb
63.28 Nm
46.673 ft-lb
50.624 Nm
37.339 ft-lb
42.187 56.249
A2-70 Stainless 39.143 Nm
28.87 ft-lb
35.228 Nm
25.983 ft-lb
29.357 Nm
21.653 ft-lb
23.486 Nm
17.322 ft-lb
19.571 26.095
A4-80 Marine Stainless 52.19 Nm
38.493 ft-lb
46.971 Nm
34.644 ft-lb
39.143 Nm
28.87 ft-lb
31.314 Nm
23.096 ft-lb
26.095 34.793

Frequently Asked Engineering Questions (M10 x 1.5 Class 10.9)

What is the recommended tightening torque for a M10 x 1.5 Class 10.9 bolt?
For a M10 x 1.5 ISO Metric Property Class 10.9 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 72.196 N·m (53.249 ft-lbs / 638.99 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 54.147 N·m (39.937 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 43.318 N·m (31.95 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M10 x 1.5 internal threads?
The standard cut tap drill size for M10 x 1.5 is 8.5 mm (0.3346" / 8.5 mm), which delivers approximately 92.4% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 9.188 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M10 x 1.5 Class 10.9 fastener develop?
With a tensile stress area (As) of 57.989 mm² (0.08988 in²) and a nominal proof stress of 830 MPa (1,20,381 psi), a M10 x 1.5 Class 10.9 fastener possesses an ultimate proof load of 48.131 kN (10,820.3 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 36.098 kN (8,115.2 lbf) across the joint interface.
What clearance hole diameters should be drilled for M10 x 1.5 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M10 x 1.5 fastener are: Close Fit = 10.5 mm (0.4134"), Normal Fit = 11 mm (0.4331"), and Loose Fit = 12 mm (0.4724"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.