Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

M12 x 1.5 Class 10.9 Torque & Tap Drill Spec

ISO 898-1

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
131.66 N·m
97.108 ft-lbs | 1165.29 in-lbs | 13.4256 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
54.858 kN
12,332.7 lbf
Target tension across joint interface
75% Tap Drill d - P
10.5 mm
10.5 mm (92.4% Eng.)
50% Hard Metal Drill: 11.188 mm
Direct Engineering Specification Summary

The recommended tightening torque for a M12 x 1.5 Class 10.9 bolt is 131.66 N·m (97.108 ft-lbs) when dry (K=0.20) and 98.745 N·m (72.831 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 54.858 kN (12,332.7 lbf) at 75% proof load. Standard 75% tap drill is 10.5 mm.

Thread & Hole Blueprint Visualizer

ISO 261 / ISO 965-1 (Metric 60°)
d = 12 mm (0.4724") P = 1.5 mm M12 x 1.5 Close: 13mm Normal: 13.5mm Loose: 14.5mm
Stress Area (As) 88.126 mm²
Pitch Diameter (d2) 11.026 mm
Minor Diameter (d1) 10.376 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (12 − 0.9382 × 1.5)² = 88.126 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 88.126 mm² × 830 N/mm² = 73145 N (73.145 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 73145 N = 54858 N (54.858 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 12 mm × 54858 N) / 1000 = 131.66 N·m (97.108 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

M12 x 1.5 Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: M12 x 1.5
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Class 8.8 95.176 Nm
70.198 ft-lb
85.658 Nm
63.178 ft-lb
71.382 Nm
52.649 ft-lb
57.106 Nm
42.119 ft-lb
39.657 52.876
Class 10.9 CURRENT 131.66 Nm
97.108 ft-lb
118.494 Nm
87.397 ft-lb
98.745 Nm
72.831 ft-lb
78.996 Nm
58.265 ft-lb
54.858 73.145
Class 12.9 153.868 Nm
113.487 ft-lb
138.481 Nm
102.138 ft-lb
115.401 Nm
85.115 ft-lb
92.321 Nm
68.092 ft-lb
64.112 85.482
A2-70 Stainless 71.382 Nm
52.649 ft-lb
64.244 Nm
47.384 ft-lb
53.537 Nm
39.487 ft-lb
42.829 Nm
31.589 ft-lb
29.743 39.657
A4-80 Marine Stainless 95.176 Nm
70.198 ft-lb
85.658 Nm
63.178 ft-lb
71.382 Nm
52.649 ft-lb
57.106 Nm
42.119 ft-lb
39.657 52.876

Frequently Asked Engineering Questions (M12 x 1.5 Class 10.9)

What is the recommended tightening torque for a M12 x 1.5 Class 10.9 bolt?
For a M12 x 1.5 ISO Metric Property Class 10.9 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 131.66 N·m (97.108 ft-lbs / 1165.29 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 98.745 N·m (72.831 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 78.996 N·m (58.265 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M12 x 1.5 internal threads?
The standard cut tap drill size for M12 x 1.5 is 10.5 mm (0.4134" / 10.5 mm), which delivers approximately 92.4% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 11.188 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M12 x 1.5 Class 10.9 fastener develop?
With a tensile stress area (As) of 88.126 mm² (0.1366 in²) and a nominal proof stress of 830 MPa (1,20,381 psi), a M12 x 1.5 Class 10.9 fastener possesses an ultimate proof load of 73.145 kN (16,443.6 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 54.858 kN (12,332.7 lbf) across the joint interface.
What clearance hole diameters should be drilled for M12 x 1.5 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M12 x 1.5 fastener are: Close Fit = 13 mm (0.5118"), Normal Fit = 13.5 mm (0.5315"), and Loose Fit = 14.5 mm (0.5709"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.