M14 x 2.0 Class 12.9 Torque & Tap Drill Spec
ISO 898-1Live Joint Clamp & Torque Engine
K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
235.149 N·m
173.437 ft-lbs | 2081.25 in-lbs | 23.9785 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
83.982 kN
18,879.9 lbf
Target tension across joint interface
75% Tap Drill d - P
12 mm
12 mm (92.4% Eng.)
50% Hard Metal Drill: 12.917 mm
Direct Engineering Specification Summary
The recommended tightening torque for a M14 x 2.0 Class 12.9 bolt is 235.149 N·m (173.437 ft-lbs) when dry (K=0.20) and 176.362 N·m (130.078 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 83.982 kN (18,879.9 lbf) at 75% proof load. Standard 75% tap drill is 12 mm.
Thread & Hole Blueprint Visualizer
ISO 261 / ISO 965-1 (Metric 60°) Stress Area (As) 115.439 mm²
Pitch Diameter (d2) 12.701 mm
Minor Diameter (d1) 11.835 mm
Step-by-Step Mathematical Derivation
VDI 2230 / ISO 898-1Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (14 − 0.9382 × 2)² = 115.439 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 115.439 mm² × 970 N/mm² = 111976 N (111.976 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 111976 N = 83982 N (83.982 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 14 mm × 83982 N) / 1000 = 235.149 N·m (173.437 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.
M14 x 2.0 Torque Across All Grades & Friction Conditions
Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.
| Grade / Class | Dry (K=0.20) | Zinc (K=0.18) | Oil (K=0.15) | Moly (K=0.12) | Clamp (kN) | Proof (kN) |
|---|---|---|---|---|---|---|
| Class 8.8 | 145.453 Nm 107.281 ft-lb | 130.908 Nm 96.553 ft-lb | 109.09 Nm 80.461 ft-lb | 87.272 Nm 64.368 ft-lb | 51.948 | 69.263 |
| Class 10.9 | 201.21 Nm 148.405 ft-lb | 181.089 Nm 133.565 ft-lb | 150.908 Nm 111.304 ft-lb | 120.726 Nm 89.043 ft-lb | 71.861 | 95.814 |
| Class 12.9 CURRENT | 235.149 Nm 173.437 ft-lb | 211.634 Nm 156.093 ft-lb | 176.362 Nm 130.078 ft-lb | 141.09 Nm 104.062 ft-lb | 83.982 | 111.976 |
| A2-70 Stainless | 109.09 Nm 80.461 ft-lb | 98.181 Nm 72.414 ft-lb | 81.817 Nm 60.345 ft-lb | 65.454 Nm 48.276 ft-lb | 38.961 | 51.948 |
| A4-80 Marine Stainless | 145.453 Nm 107.281 ft-lb | 130.908 Nm 96.553 ft-lb | 109.09 Nm 80.461 ft-lb | 87.272 Nm 64.368 ft-lb | 51.948 | 69.263 |
Frequently Asked Engineering Questions (M14 x 2.0 Class 12.9)
What is the recommended tightening torque for a M14 x 2.0 Class 12.9 bolt?
For a M14 x 2.0 ISO Metric Property Class 12.9 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 235.149 N·m (173.437 ft-lbs / 2081.25 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 176.362 N·m (130.078 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 141.09 N·m (104.062 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M14 x 2.0 internal threads?
The standard cut tap drill size for M14 x 2.0 is 12 mm (0.4724" / 12 mm), which delivers approximately 92.4% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 12.917 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M14 x 2.0 Class 12.9 fastener develop?
With a tensile stress area (As) of 115.439 mm² (0.17893 in²) and a nominal proof stress of 970 MPa (1,40,687 psi), a M14 x 2.0 Class 12.9 fastener possesses an ultimate proof load of 111.976 kN (25,173.2 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 83.982 kN (18,879.9 lbf) across the joint interface.
What clearance hole diameters should be drilled for M14 x 2.0 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M14 x 2.0 fastener are: Close Fit = 15 mm (0.5906"), Normal Fit = 15.5 mm (0.6102"), and Loose Fit = 16.5 mm (0.6496"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.
Recent Calculations
No recent calculations saved yet.