Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

M36 x 4.0 Class 8.8 Torque & Tap Drill Spec

ISO 898-1

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
2646.176 N·m
1951.719 ft-lbs | 23420.63 in-lbs | 269.8349 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
367.524 kN
82,622.8 lbf
Target tension across joint interface
75% Tap Drill d - P
32 mm
32 mm (92.4% Eng.)
50% Hard Metal Drill: 33.835 mm
Direct Engineering Specification Summary

The recommended tightening torque for a M36 x 4.0 Class 8.8 bolt is 2646.176 N·m (1951.719 ft-lbs) when dry (K=0.20) and 1984.632 N·m (1463.789 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 367.524 kN (82,622.8 lbf) at 75% proof load. Standard 75% tap drill is 32 mm.

Thread & Hole Blueprint Visualizer

ISO 261 / ISO 965-1 (Metric 60°)
d = 36 mm (1.4173") P = 4 mm M36 x 4.0 Close: 37mm Normal: 39mm Loose: 42mm
Stress Area (As) 816.721 mm²
Pitch Diameter (d2) 33.402 mm
Minor Diameter (d1) 31.67 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (36 − 0.9382 × 4)² = 816.721 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 816.721 mm² × 600 N/mm² = 490033 N (490.033 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 490033 N = 367524 N (367.524 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 36 mm × 367524 N) / 1000 = 2646.176 N·m (1951.719 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

M36 x 4.0 Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: M36 x 4.0
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Class 8.8 CURRENT 2646.176 Nm
1951.719 ft-lb
2381.558 Nm
1756.547 ft-lb
1984.632 Nm
1463.789 ft-lb
1587.706 Nm
1171.032 ft-lb
367.524 490.033
Class 10.9 3660.544 Nm
2699.878 ft-lb
3294.489 Nm
2429.891 ft-lb
2745.408 Nm
2024.909 ft-lb
2196.326 Nm
1619.927 ft-lb
508.409 677.878
Class 12.9 4277.985 Nm
3155.28 ft-lb
3850.186 Nm
2839.752 ft-lb
3208.488 Nm
2366.46 ft-lb
2566.791 Nm
1893.168 ft-lb
594.165 792.219
A2-70 Stainless 1984.632 Nm
1463.789 ft-lb
1786.169 Nm
1317.411 ft-lb
1488.474 Nm
1097.842 ft-lb
1190.779 Nm
878.274 ft-lb
275.643 367.524
A4-80 Marine Stainless 2646.176 Nm
1951.719 ft-lb
2381.558 Nm
1756.547 ft-lb
1984.632 Nm
1463.789 ft-lb
1587.706 Nm
1171.032 ft-lb
367.524 490.033

Frequently Asked Engineering Questions (M36 x 4.0 Class 8.8)

What is the recommended tightening torque for a M36 x 4.0 Class 8.8 bolt?
For a M36 x 4.0 ISO Metric Property Class 8.8 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 2646.176 N·m (1951.719 ft-lbs / 23420.63 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 1984.632 N·m (1463.789 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 1587.706 N·m (1171.032 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M36 x 4.0 internal threads?
The standard cut tap drill size for M36 x 4.0 is 32 mm (1.2598" / 32 mm), which delivers approximately 92.4% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 33.835 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M36 x 4.0 Class 8.8 fastener develop?
With a tensile stress area (As) of 816.721 mm² (1.26592 in²) and a nominal proof stress of 600 MPa (87,023 psi), a M36 x 4.0 Class 8.8 fastener possesses an ultimate proof load of 490.033 kN (1,10,163.7 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 367.524 kN (82,622.8 lbf) across the joint interface.
What clearance hole diameters should be drilled for M36 x 4.0 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M36 x 4.0 fastener are: Close Fit = 37 mm (1.4567"), Normal Fit = 39 mm (1.5354"), and Loose Fit = 42 mm (1.6535"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.