Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

M8 x 1.0 Class 12.9 Torque & Tap Drill Spec

ISO 898-1

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
45.59 N·m
33.626 ft-lbs | 403.51 in-lbs | 4.6489 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
28.494 kN
6,405.7 lbf
Target tension across joint interface
75% Tap Drill d - P
7 mm
7.0 mm (92.4% Eng.)
50% Hard Metal Drill: 7.459 mm
Direct Engineering Specification Summary

The recommended tightening torque for a M8 x 1.0 Class 12.9 bolt is 45.59 N·m (33.626 ft-lbs) when dry (K=0.20) and 34.193 N·m (25.219 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 28.494 kN (6,405.7 lbf) at 75% proof load. Standard 75% tap drill is 7.0 mm.

Thread & Hole Blueprint Visualizer

ISO 261 / ISO 965-1 (Metric 60°)
d = 8 mm (0.315") P = 1 mm M8 x 1.0 Close: 8.4mm Normal: 9mm Loose: 10mm
Stress Area (As) 39.167 mm²
Pitch Diameter (d2) 7.35 mm
Minor Diameter (d1) 6.917 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (8 − 0.9382 × 1)² = 39.167 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 39.167 mm² × 970 N/mm² = 37992 N (37.992 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 37992 N = 28494 N (28.494 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 8 mm × 28494 N) / 1000 = 45.59 N·m (33.626 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

M8 x 1.0 Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: M8 x 1.0
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Class 8.8 28.2 Nm
20.799 ft-lb
25.38 Nm
18.719 ft-lb
21.15 Nm
15.6 ft-lb
16.92 Nm
12.48 ft-lb
17.625 23.5
Class 10.9 39.01 Nm
28.773 ft-lb
35.109 Nm
25.895 ft-lb
29.258 Nm
21.579 ft-lb
23.406 Nm
17.264 ft-lb
24.381 32.509
Class 12.9 CURRENT 45.59 Nm
33.626 ft-lb
41.031 Nm
30.263 ft-lb
34.193 Nm
25.219 ft-lb
27.354 Nm
20.175 ft-lb
28.494 37.992
A2-70 Stainless 21.15 Nm
15.6 ft-lb
19.035 Nm
14.04 ft-lb
15.863 Nm
11.7 ft-lb
12.69 Nm
9.36 ft-lb
13.219 17.625
A4-80 Marine Stainless 28.2 Nm
20.799 ft-lb
25.38 Nm
18.719 ft-lb
21.15 Nm
15.6 ft-lb
16.92 Nm
12.48 ft-lb
17.625 23.5

Frequently Asked Engineering Questions (M8 x 1.0 Class 12.9)

What is the recommended tightening torque for a M8 x 1.0 Class 12.9 bolt?
For a M8 x 1.0 ISO Metric Property Class 12.9 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 45.59 N·m (33.626 ft-lbs / 403.51 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 34.193 N·m (25.219 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 27.354 N·m (20.175 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M8 x 1.0 internal threads?
The standard cut tap drill size for M8 x 1.0 is 7.0 mm (0.2756" / 7 mm), which delivers approximately 92.4% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 7.459 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M8 x 1.0 Class 12.9 fastener develop?
With a tensile stress area (As) of 39.167 mm² (0.06071 in²) and a nominal proof stress of 970 MPa (1,40,687 psi), a M8 x 1.0 Class 12.9 fastener possesses an ultimate proof load of 37.992 kN (8,540.9 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 28.494 kN (6,405.7 lbf) across the joint interface.
What clearance hole diameters should be drilled for M8 x 1.0 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M8 x 1.0 fastener are: Close Fit = 8.4 mm (0.3307"), Normal Fit = 9 mm (0.3543"), and Loose Fit = 10 mm (0.3937"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.