1018 Mild Carbon Steel (Cold Rolled) — 1/4" (0.250 in) 2-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 1018 Mild Carbon Steel (Cold Rolled) with a 1/4" (0.250 in) 2-flute TiAlN carbide end mill, the recommended spindle speed is 12,031 RPM at 240 m/min (787.4 SFM), with a profiling feed rate of 669 mm/min (26.2 IPM) and adjusted chip load of 0.0278 mm/tooth, achieving a material removal rate of 10.13 cm³/min (0.61 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math1018 Mild Carbon Steel (Cold Rolled) (1/4" (0.250 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 6.35 mm | 3.17 mm | 1× | 436 | 17.1 | 8.78 | 0.27 |
| Slotting (100% WOC) | 3F | 6.35 mm | 3.17 mm | 1× | 653 | 25.6 | 13.14 | 0.41 |
| Slotting (100% WOC) | 4F | 6.35 mm | 3.17 mm | 1× | 871 | 34.2 | 17.53 | 0.55 |
| Profiling / HEM (25% WOC) CURRENT | 2F | 1.59 mm | 9.52 mm | 1.1541× | 669 | 26.2 | 10.13 | 0.32 |
| Profiling / HEM (25% WOC) | 3F | 1.59 mm | 9.52 mm | 1.1541× | 1,003 | 39.3 | 15.18 | 0.47 |
| Profiling / HEM (25% WOC) | 4F | 1.59 mm | 9.52 mm | 1.1541× | 1,338 | 52.5 | 20.25 | 0.63 |
| Adaptive Clearing (10% WOC) | 2F | 0.64 mm | 12.7 mm | 1.6609× | 962 | 37.8 | 7.82 | 0.24 |
| Adaptive Clearing (10% WOC) | 3F | 0.64 mm | 12.7 mm | 1.6609× | 1,444 | 56.7 | 11.74 | 0.37 |
| Adaptive Clearing (10% WOC) | 4F | 0.64 mm | 12.7 mm | 1.6609× | 1,925 | 75.6 | 15.65 | 0.49 |
Shop-Floor Machining Strategy for 1018 Mild Carbon Steel (Cold Rolled)
Work Hardening: ModerateFlood Coolant with 7-9% Soluble Oil or Dry with Air Blast for TiAlN Carbide
Pressure: 5 to 10 bar
With TiAlN coated carbide, dry cutting with air blast prevents thermal shock cycling on cutting edges.
Chip Flow: Low carbon steel can produce continuous gummy stringers if feed rate is too low. Keep chip load elevated.
Milling Direction: Always climb mill to manage tool heat dissipation into chips.
- Avoid rubbing at low feed rates. Feed fast enough to produce C-shaped curled blue/straw chips.
- TiAlN coating thrives on heat; avoid intermittent wet cooling that causes micro-cracking.
- 4-flute end mills deliver the best surface finish and wall straightness.
Frequently Asked CNC Questions (1018 Mild Carbon Steel (Cold Rolled) / 1/4" (0.250 in))
What is the recommended RPM for milling 1018 Mild Carbon Steel (Cold Rolled) with a 1/4" (0.250 in) end mill?
What table feed rate and chip load should I program for 1/4" (0.250 in) in 1018 Mild Carbon Steel (Cold Rolled)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 1018 Mild Carbon Steel (Cold Rolled)?
Recent Calculations
No recent calculations saved yet.