Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

1018 Mild Carbon Steel (Cold Rolled) — 3/8" (0.375 in) 2-Flute Speeds & Feeds

ISO Group P 126 HB / 71 HRB

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
8,020 RPM
Surface Speed: 240 m/min (787.4 SFM)
Table Feed Rate F = RPM·z·fz
619 mm/min
24.4 IPM
Plunge/Ramp Rate: 217 mm/min
Adjusted Chip Load CTF: 1.1549×
0.0386 mm/t
0.00152 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
21.05 cm³/min
1.29 in³/min
Power Required: 0.66 kW (0.88 HP)
Direct CNC Machining Solution

For milling 1018 Mild Carbon Steel (Cold Rolled) with a 3/8" (0.375 in) 2-flute TiAlN carbide end mill, the recommended spindle speed is 8,020 RPM at 240 m/min (787.4 SFM), with a profiling feed rate of 619 mm/min (24.4 IPM) and adjusted chip load of 0.0386 mm/tooth, achieving a material removal rate of 21.05 cm³/min (1.29 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
1018 Mild Carbon Steel (Cold Rolled) Stock CLIMB D = 9.525 mm (0.375") ae = 2.38 mm ap = 14.29 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1549×
Spindle Torque 0.63 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (240 × 1000) / (π × 9.525) = 8,020 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 2.38/9.525 = 0.25 → CTF = 1.1549×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0334 mm × 1.1549 = 0.0386 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 8,020 × 2 × 0.0386 = 619 mm/min (24.4 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (14.29 × 2.38 × 619) / 1000 = 21.05 cm³/min (1.29 in³/min)
Specific Cutting Force (kc) for 1018 Mild Carbon Steel (Cold Rolled): 1500 N/mm². Spindle drive efficiency η = 0.80.

1018 Mild Carbon Steel (Cold Rolled) (3/8" (0.375 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 3/8" (0.375 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 9.53 mm 4.76 mm 1× 401 15.7 18.19 0.57
Slotting (100% WOC) 3F 9.53 mm 4.76 mm 1× 602 23.6 27.31 0.85
Slotting (100% WOC) 4F 9.53 mm 4.76 mm 1× 802 31.4 36.38 1.14
Profiling / HEM (25% WOC) CURRENT 2F 2.38 mm 14.29 mm 1.1549× 619 24.4 21.05 0.66
Profiling / HEM (25% WOC) 3F 2.38 mm 14.29 mm 1.1549× 929 36.6 31.6 0.99
Profiling / HEM (25% WOC) 4F 2.38 mm 14.29 mm 1.1549× 1,238 48.8 42.1 1.32
Adaptive Clearing (10% WOC) 2F 0.95 mm 19.05 mm 1.6686× 893 35.1 16.16 0.51
Adaptive Clearing (10% WOC) 3F 0.95 mm 19.05 mm 1.6686× 1,340 52.7 24.25 0.76
Adaptive Clearing (10% WOC) 4F 0.95 mm 19.05 mm 1.6686× 1,787 70.3 32.34 1.01

Shop-Floor Machining Strategy for 1018 Mild Carbon Steel (Cold Rolled)

Work Hardening: Moderate
Coolant & Lubrication Protocol

Flood Coolant with 7-9% Soluble Oil or Dry with Air Blast for TiAlN Carbide

Pressure: 5 to 10 bar

With TiAlN coated carbide, dry cutting with air blast prevents thermal shock cycling on cutting edges.

Chip Evacuation & Tool Path Guidance

Chip Flow: Low carbon steel can produce continuous gummy stringers if feed rate is too low. Keep chip load elevated.

Milling Direction: Always climb mill to manage tool heat dissipation into chips.

Expert Machinist Tips:
  • Avoid rubbing at low feed rates. Feed fast enough to produce C-shaped curled blue/straw chips.
  • TiAlN coating thrives on heat; avoid intermittent wet cooling that causes micro-cracking.
  • 4-flute end mills deliver the best surface finish and wall straightness.

Frequently Asked CNC Questions (1018 Mild Carbon Steel (Cold Rolled) / 3/8" (0.375 in))

What is the recommended RPM for milling 1018 Mild Carbon Steel (Cold Rolled) with a 3/8" (0.375 in) end mill?
For a 3/8" (0.375 in) (9.525 mm) TiAlN coated carbide end mill in 1018 Mild Carbon Steel (Cold Rolled), the baseline surface cutting speed is 240 m/min (787.4 SFM), which translates to a calculated spindle speed of 8,020 RPM. If using uncoated carbide, reduce surface speed to 200 m/min (650 SFM / 6684 RPM). For HSS cutters, speed must be restricted to 35 m/min (1170 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 3/8" (0.375 in) in 1018 Mild Carbon Steel (Cold Rolled)?
At 8,020 RPM with a 2-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0386 mm/tooth (0.00152"/tooth) after applying a radial chip thinning factor (CTF) of 1.1549×. This yields a table feed rate of 619 mm/min (24.4 IPM). Ramping or plunging into material should be limited to 35% of table feed (217 mm/min / 8.5 IPM) at an entry ramp angle of 3°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 2.38 mm), the Chip Thinning Factor is 1.1549×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 1018 Mild Carbon Steel (Cold Rolled)?
Flood Coolant with 7-9% Soluble Oil or Dry with Air Blast for TiAlN Carbide. Pressure specification: 5 to 10 bar. Engineering rationale: With TiAlN coated carbide, dry cutting with air blast prevents thermal shock cycling on cutting edges.