Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

1018 Mild Carbon Steel (Cold Rolled) — 12 mm 3-Flute Speeds & Feeds

ISO Group P 126 HB / 71 HRB

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
6,366 RPM
Surface Speed: 240 m/min (787.4 SFM)
Table Feed Rate F = RPM·z·fz
886 mm/min
34.9 IPM
Plunge/Ramp Rate: 310 mm/min
Adjusted Chip Load CTF: 1.1547×
0.0464 mm/t
0.00183 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
47.84 cm³/min
2.92 in³/min
Power Required: 1.49 kW (2 HP)
Direct CNC Machining Solution

For milling 1018 Mild Carbon Steel (Cold Rolled) with a 12 mm 3-flute TiAlN carbide end mill, the recommended spindle speed is 6,366 RPM at 240 m/min (787.4 SFM), with a profiling feed rate of 886 mm/min (34.9 IPM) and adjusted chip load of 0.0464 mm/tooth, achieving a material removal rate of 47.84 cm³/min (2.92 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
1018 Mild Carbon Steel (Cold Rolled) Stock CLIMB D = 12 mm (0.4724") ae = 3 mm ap = 18 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1547×
Spindle Torque 1.8 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (240 × 1000) / (π × 12) = 6,366 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 3/12 = 0.25 → CTF = 1.1547×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0402 mm × 1.1547 = 0.0464 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 6,366 × 3 × 0.0464 = 886 mm/min (34.9 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (18 × 3 × 886) / 1000 = 47.84 cm³/min (2.92 in³/min)
Specific Cutting Force (kc) for 1018 Mild Carbon Steel (Cold Rolled): 1500 N/mm². Spindle drive efficiency η = 0.80.

1018 Mild Carbon Steel (Cold Rolled) (12 mm) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 12 mm
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 12 mm 6 mm 1× 383 15.2 27.58 0.86
Slotting (100% WOC) 3F 12 mm 6 mm 1× 575 22.7 41.4 1.29
Slotting (100% WOC) 4F 12 mm 6 mm 1× 766 30.3 55.15 1.72
Profiling / HEM (25% WOC) 2F 3 mm 18 mm 1.1547× 591 23.3 31.91 1
Profiling / HEM (25% WOC) CURRENT 3F 3 mm 18 mm 1.1547× 886 34.9 47.84 1.49
Profiling / HEM (25% WOC) 4F 3 mm 18 mm 1.1547× 1,182 46.6 63.83 1.99
Adaptive Clearing (10% WOC) 2F 1.2 mm 24 mm 1.6667× 853 33.6 24.57 0.77
Adaptive Clearing (10% WOC) 3F 1.2 mm 24 mm 1.6667× 1,280 50.4 36.86 1.15
Adaptive Clearing (10% WOC) 4F 1.2 mm 24 mm 1.6667× 1,706 67.2 49.13 1.54

Shop-Floor Machining Strategy for 1018 Mild Carbon Steel (Cold Rolled)

Work Hardening: Moderate
Coolant & Lubrication Protocol

Flood Coolant with 7-9% Soluble Oil or Dry with Air Blast for TiAlN Carbide

Pressure: 5 to 10 bar

With TiAlN coated carbide, dry cutting with air blast prevents thermal shock cycling on cutting edges.

Chip Evacuation & Tool Path Guidance

Chip Flow: Low carbon steel can produce continuous gummy stringers if feed rate is too low. Keep chip load elevated.

Milling Direction: Always climb mill to manage tool heat dissipation into chips.

Expert Machinist Tips:
  • Avoid rubbing at low feed rates. Feed fast enough to produce C-shaped curled blue/straw chips.
  • TiAlN coating thrives on heat; avoid intermittent wet cooling that causes micro-cracking.
  • 4-flute end mills deliver the best surface finish and wall straightness.

Frequently Asked CNC Questions (1018 Mild Carbon Steel (Cold Rolled) / 12 mm)

What is the recommended RPM for milling 1018 Mild Carbon Steel (Cold Rolled) with a 12 mm end mill?
For a 12 mm (12 mm) TiAlN coated carbide end mill in 1018 Mild Carbon Steel (Cold Rolled), the baseline surface cutting speed is 240 m/min (787.4 SFM), which translates to a calculated spindle speed of 6,366 RPM. If using uncoated carbide, reduce surface speed to 200 m/min (650 SFM / 5305 RPM). For HSS cutters, speed must be restricted to 35 m/min (928 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 12 mm in 1018 Mild Carbon Steel (Cold Rolled)?
At 6,366 RPM with a 3-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0464 mm/tooth (0.00183"/tooth) after applying a radial chip thinning factor (CTF) of 1.1547×. This yields a table feed rate of 886 mm/min (34.9 IPM). Ramping or plunging into material should be limited to 35% of table feed (310 mm/min / 12.2 IPM) at an entry ramp angle of 2.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 3 mm), the Chip Thinning Factor is 1.1547×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 1018 Mild Carbon Steel (Cold Rolled)?
Flood Coolant with 7-9% Soluble Oil or Dry with Air Blast for TiAlN Carbide. Pressure specification: 5 to 10 bar. Engineering rationale: With TiAlN coated carbide, dry cutting with air blast prevents thermal shock cycling on cutting edges.