Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) — 20 mm 4-Flute Speeds & Feeds

ISO Group M / H 388 HB / 40-42 HRC

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
1,751 RPM
Surface Speed: 110 m/min (360.9 SFM)
Table Feed Rate F = RPM·z·fz
310 mm/min
12.2 IPM
Plunge/Ramp Rate: 109 mm/min
Adjusted Chip Load CTF: 1.1547×
0.0443 mm/t
0.00174 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
46.5 cm³/min
2.84 in³/min
Power Required: 2.52 kW (3.38 HP)
Direct CNC Machining Solution

For milling 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) with a 20 mm 4-flute TiAlN carbide end mill, the recommended spindle speed is 1,751 RPM at 110 m/min (360.9 SFM), with a profiling feed rate of 310 mm/min (12.2 IPM) and adjusted chip load of 0.0443 mm/tooth, achieving a material removal rate of 46.5 cm³/min (2.84 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) Stock CLIMB D = 20 mm (0.7874") ae = 5 mm ap = 30 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1547×
Spindle Torque 11.02 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (110 × 1000) / (π × 20) = 1,751 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 5/20 = 0.25 → CTF = 1.1547×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0384 mm × 1.1547 = 0.0443 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 1,751 × 4 × 0.0443 = 310 mm/min (12.2 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (30 × 5 × 310) / 1000 = 46.5 cm³/min (2.84 in³/min)
Specific Cutting Force (kc) for 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC): 2600 N/mm². Spindle drive efficiency η = 0.80.

17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) (20 mm) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 20 mm
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 20 mm 10 mm 1× 101 4 20.2 1.09
Slotting (100% WOC) 3F 20 mm 10 mm 1× 151 5.9 30.2 1.64
Slotting (100% WOC) 4F 20 mm 10 mm 1× 202 7.9 40.4 2.19
Profiling / HEM (25% WOC) 2F 5 mm 30 mm 1.1547× 155 6.1 23.25 1.26
Profiling / HEM (25% WOC) 3F 5 mm 30 mm 1.1547× 233 9.1 34.95 1.89
Profiling / HEM (25% WOC) CURRENT 4F 5 mm 30 mm 1.1547× 310 12.2 46.5 2.52
Adaptive Clearing (10% WOC) 2F 2 mm 40 mm 1.6667× 224 8.8 17.92 0.97
Adaptive Clearing (10% WOC) 3F 2 mm 40 mm 1.6667× 336 13.2 26.88 1.46
Adaptive Clearing (10% WOC) 4F 2 mm 40 mm 1.6667× 448 17.7 35.84 1.94

Shop-Floor Machining Strategy for 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)

Work Hardening: High
Coolant & Lubrication Protocol

High-Pressure Flood Coolant with Synthetic Water-Soluble Fluid

Pressure: 30 to 70 bar

Heat dissipation from the shear zone prevents thermal tempering and edge fatigue.

Chip Evacuation & Tool Path Guidance

Chip Flow: Crisp, tight curled chips; high cutting forces generated.

Milling Direction: Always climb mill.

Expert Machinist Tips:
  • In H900 condition, tool rigidity and low runout (<0.005 mm) are required to avoid chipped flutes.
  • Use thick-core end mills designed for hardened steels (4-5 flutes).
  • Trochoidal / dynamic milling with light radial engagement (6-10%) increases tool life by 300%.

Frequently Asked CNC Questions (17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) / 20 mm)

What is the recommended RPM for milling 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) with a 20 mm end mill?
For a 20 mm (20 mm) TiAlN coated carbide end mill in 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC), the baseline surface cutting speed is 110 m/min (360.9 SFM), which translates to a calculated spindle speed of 1,751 RPM. If using uncoated carbide, reduce surface speed to 85 m/min (280 SFM / 1353 RPM). For HSS cutters, speed must be restricted to 14 m/min (223 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 20 mm in 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)?
At 1,751 RPM with a 4-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0443 mm/tooth (0.00174"/tooth) after applying a radial chip thinning factor (CTF) of 1.1547×. This yields a table feed rate of 310 mm/min (12.2 IPM). Ramping or plunging into material should be limited to 35% of table feed (109 mm/min / 4.3 IPM) at an entry ramp angle of 1.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 5 mm), the Chip Thinning Factor is 1.1547×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)?
High-Pressure Flood Coolant with Synthetic Water-Soluble Fluid. Pressure specification: 30 to 70 bar. Engineering rationale: Heat dissipation from the shear zone prevents thermal tempering and edge fatigue.