Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

7075-T6 Aerospace Aluminum — 20 mm 4-Flute Speeds & Feeds

ISO Group N 150 HB / 87 HRB

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
9,231 RPM
Surface Speed: 580 m/min (1902.9 SFM)
Table Feed Rate F = RPM·z·fz
3,279 mm/min
129.2 IPM
Plunge/Ramp Rate: 1148 mm/min
Adjusted Chip Load CTF: 1.1547×
0.0888 mm/t
0.0035 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
491.85 cm³/min
30.05 in³/min
Power Required: 8.71 kW (11.68 HP)
Direct CNC Machining Solution

For milling 7075-T6 Aerospace Aluminum with a 20 mm 4-flute TiAlN carbide end mill, the recommended spindle speed is 9,231 RPM at 580 m/min (1902.9 SFM), with a profiling feed rate of 3,279 mm/min (129.2 IPM) and adjusted chip load of 0.0888 mm/tooth, achieving a material removal rate of 491.85 cm³/min (30.05 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
7075-T6 Aerospace Aluminum Stock CLIMB D = 20 mm (0.7874") ae = 5 mm ap = 30 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1547×
Spindle Torque 7.21 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (580 × 1000) / (π × 20) = 9,231 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 5/20 = 0.25 → CTF = 1.1547×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0769 mm × 1.1547 = 0.0888 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 9,231 × 4 × 0.0888 = 3,279 mm/min (129.2 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (30 × 5 × 3279) / 1000 = 491.85 cm³/min (30.05 in³/min)
Specific Cutting Force (kc) for 7075-T6 Aerospace Aluminum: 850 N/mm². Spindle drive efficiency η = 0.80.

7075-T6 Aerospace Aluminum (20 mm) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 20 mm
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 20 mm 10 mm 1× 1,065 41.9 213 3.77
Slotting (100% WOC) 3F 20 mm 10 mm 1× 1,598 62.9 319.6 5.66
Slotting (100% WOC) 4F 20 mm 10 mm 1× 2,131 83.8 426.2 7.55
Profiling / HEM (25% WOC) 2F 5 mm 30 mm 1.1547× 1,639 64.6 245.85 4.35
Profiling / HEM (25% WOC) 3F 5 mm 30 mm 1.1547× 2,459 96.9 368.85 6.53
Profiling / HEM (25% WOC) CURRENT 4F 5 mm 30 mm 1.1547× 3,279 129.2 491.85 8.71
Adaptive Clearing (10% WOC) 2F 2 mm 40 mm 1.6667× 2,367 93.2 189.36 3.35
Adaptive Clearing (10% WOC) 3F 2 mm 40 mm 1.6667× 3,550 139.8 284 5.03
Adaptive Clearing (10% WOC) 4F 2 mm 40 mm 1.6667× 4,734 186.5 378.72 6.71

Shop-Floor Machining Strategy for 7075-T6 Aerospace Aluminum

Work Hardening: Low
Coolant & Lubrication Protocol

Flood Coolant with 8-10% Synthetic Soluble Oil Concentration

Pressure: Standard flood (5 bar minimum)

Zinc-alloyed aluminum chips break cleaner than 6061, with superior surface finish.

Chip Evacuation & Tool Path Guidance

Chip Flow: Excellent short crisp chips compared to 6061. Can run 3-flute tools at aggressive feeds.

Milling Direction: Climb milling gives mirror surface finishes.

Expert Machinist Tips:
  • High zinc content gives higher tensile strength; chips shear off crisply.
  • Maintain tool rigidity; deflection causes dimensional drift on tight aerospace tolerances.
  • Ideal candidate for High-Speed Machining (HSM) with high axial depth and light radial stepover.

Frequently Asked CNC Questions (7075-T6 Aerospace Aluminum / 20 mm)

What is the recommended RPM for milling 7075-T6 Aerospace Aluminum with a 20 mm end mill?
For a 20 mm (20 mm) TiAlN coated carbide end mill in 7075-T6 Aerospace Aluminum, the baseline surface cutting speed is 580 m/min (1902.9 SFM), which translates to a calculated spindle speed of 9,231 RPM. If using uncoated carbide, reduce surface speed to 480 m/min (1600 SFM / 7639 RPM). For HSS cutters, speed must be restricted to 100 m/min (1592 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 20 mm in 7075-T6 Aerospace Aluminum?
At 9,231 RPM with a 4-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0888 mm/tooth (0.0035"/tooth) after applying a radial chip thinning factor (CTF) of 1.1547×. This yields a table feed rate of 3279 mm/min (129.2 IPM). Ramping or plunging into material should be limited to 35% of table feed (1148 mm/min / 45.2 IPM) at an entry ramp angle of 1.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 5 mm), the Chip Thinning Factor is 1.1547×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 7075-T6 Aerospace Aluminum?
Flood Coolant with 8-10% Synthetic Soluble Oil Concentration. Pressure specification: Standard flood (5 bar minimum). Engineering rationale: Zinc-alloyed aluminum chips break cleaner than 6061, with superior surface finish.