17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) — 4 mm 2-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) with a 4 mm 2-flute TiAlN carbide end mill, the recommended spindle speed is 8,754 RPM at 110 m/min (360.9 SFM), with a profiling feed rate of 214 mm/min (8.4 IPM) and adjusted chip load of 0.0122 mm/tooth, achieving a material removal rate of 1.28 cm³/min (0.08 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) (4 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 4 mm | 2 mm | 1× | 140 | 5.4 | 1.12 | 0.06 |
| Slotting (100% WOC) | 3F | 4 mm | 2 mm | 1× | 210 | 8.1 | 1.68 | 0.09 |
| Slotting (100% WOC) | 4F | 4 mm | 2 mm | 1× | 280 | 10.9 | 2.24 | 0.12 |
| Profiling / HEM (25% WOC) CURRENT | 2F | 1 mm | 6 mm | 1.1547× | 214 | 8.4 | 1.28 | 0.07 |
| Profiling / HEM (25% WOC) | 3F | 1 mm | 6 mm | 1.1547× | 320 | 12.6 | 1.92 | 0.1 |
| Profiling / HEM (25% WOC) | 4F | 1 mm | 6 mm | 1.1547× | 427 | 16.8 | 2.56 | 0.14 |
| Adaptive Clearing (10% WOC) | 2F | 0.4 mm | 8 mm | 1.6667× | 310 | 12.3 | 0.99 | 0.05 |
| Adaptive Clearing (10% WOC) | 3F | 0.4 mm | 8 mm | 1.6667× | 465 | 18.4 | 1.49 | 0.08 |
| Adaptive Clearing (10% WOC) | 4F | 0.4 mm | 8 mm | 1.6667× | 620 | 24.5 | 1.98 | 0.11 |
Shop-Floor Machining Strategy for 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)
Work Hardening: HighHigh-Pressure Flood Coolant with Synthetic Water-Soluble Fluid
Pressure: 30 to 70 bar
Heat dissipation from the shear zone prevents thermal tempering and edge fatigue.
Chip Flow: Crisp, tight curled chips; high cutting forces generated.
Milling Direction: Always climb mill.
- In H900 condition, tool rigidity and low runout (<0.005 mm) are required to avoid chipped flutes.
- Use thick-core end mills designed for hardened steels (4-5 flutes).
- Trochoidal / dynamic milling with light radial engagement (6-10%) increases tool life by 300%.
Frequently Asked CNC Questions (17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) / 4 mm)
What is the recommended RPM for milling 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) with a 4 mm end mill?
What table feed rate and chip load should I program for 4 mm in 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)?
Recent Calculations
No recent calculations saved yet.