Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) — 3 mm 2-Flute Speeds & Feeds

ISO Group M / H 388 HB / 40-42 HRC

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
11,671 RPM
Surface Speed: 110 m/min (360.9 SFM)
Table Feed Rate F = RPM·z·fz
226 mm/min
8.9 IPM
Plunge/Ramp Rate: 79 mm/min
Adjusted Chip Load CTF: 1.1547×
0.0097 mm/t
0.00038 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
0.76 cm³/min
0.05 in³/min
Power Required: 0.04 kW (0.06 HP)
Direct CNC Machining Solution

For milling 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) with a 3 mm 2-flute TiAlN carbide end mill, the recommended spindle speed is 11,671 RPM at 110 m/min (360.9 SFM), with a profiling feed rate of 226 mm/min (8.9 IPM) and adjusted chip load of 0.0097 mm/tooth, achieving a material removal rate of 0.76 cm³/min (0.05 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) Stock CLIMB D = 3 mm (0.1181") ae = 0.75 mm ap = 4.5 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1547×
Spindle Torque 0.02 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (110 × 1000) / (π × 3) = 11,671 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 0.75/3 = 0.25 → CTF = 1.1547×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0084 mm × 1.1547 = 0.0097 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 11,671 × 2 × 0.0097 = 226 mm/min (8.9 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (4.5 × 0.75 × 226) / 1000 = 0.76 cm³/min (0.05 in³/min)
Specific Cutting Force (kc) for 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC): 2600 N/mm². Spindle drive efficiency η = 0.80.

17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) (3 mm) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 3 mm
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 3 mm 1.5 mm 1× 147 5.8 0.66 0.04
Slotting (100% WOC) 3F 3 mm 1.5 mm 1× 221 8.8 0.99 0.05
Slotting (100% WOC) 4F 3 mm 1.5 mm 1× 294 11.7 1.32 0.07
Profiling / HEM (25% WOC) CURRENT 2F 0.75 mm 4.5 mm 1.1547× 226 8.9 0.76 0.04
Profiling / HEM (25% WOC) 3F 0.75 mm 4.5 mm 1.1547× 340 13.3 1.15 0.06
Profiling / HEM (25% WOC) 4F 0.75 mm 4.5 mm 1.1547× 453 17.7 1.53 0.08
Adaptive Clearing (10% WOC) 2F 0.3 mm 6 mm 1.6667× 327 12.8 0.59 0.03
Adaptive Clearing (10% WOC) 3F 0.3 mm 6 mm 1.6667× 490 19.3 0.88 0.05
Adaptive Clearing (10% WOC) 4F 0.3 mm 6 mm 1.6667× 654 25.7 1.18 0.06

Shop-Floor Machining Strategy for 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)

Work Hardening: High
Coolant & Lubrication Protocol

High-Pressure Flood Coolant with Synthetic Water-Soluble Fluid

Pressure: 30 to 70 bar

Heat dissipation from the shear zone prevents thermal tempering and edge fatigue.

Chip Evacuation & Tool Path Guidance

Chip Flow: Crisp, tight curled chips; high cutting forces generated.

Milling Direction: Always climb mill.

Expert Machinist Tips:
  • In H900 condition, tool rigidity and low runout (<0.005 mm) are required to avoid chipped flutes.
  • Use thick-core end mills designed for hardened steels (4-5 flutes).
  • Trochoidal / dynamic milling with light radial engagement (6-10%) increases tool life by 300%.

Frequently Asked CNC Questions (17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) / 3 mm)

What is the recommended RPM for milling 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) with a 3 mm end mill?
For a 3 mm (3 mm) TiAlN coated carbide end mill in 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC), the baseline surface cutting speed is 110 m/min (360.9 SFM), which translates to a calculated spindle speed of 11,671 RPM. If using uncoated carbide, reduce surface speed to 85 m/min (280 SFM / 9019 RPM). For HSS cutters, speed must be restricted to 14 m/min (1485 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 3 mm in 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)?
At 11,671 RPM with a 2-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0097 mm/tooth (0.00038"/tooth) after applying a radial chip thinning factor (CTF) of 1.1547×. This yields a table feed rate of 226 mm/min (8.9 IPM). Ramping or plunging into material should be limited to 35% of table feed (79 mm/min / 3.1 IPM) at an entry ramp angle of 3°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 0.75 mm), the Chip Thinning Factor is 1.1547×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)?
High-Pressure Flood Coolant with Synthetic Water-Soluble Fluid. Pressure specification: 30 to 70 bar. Engineering rationale: Heat dissipation from the shear zone prevents thermal tempering and edge fatigue.