17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) — 6 mm 3-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) with a 6 mm 3-flute TiAlN carbide end mill, the recommended spindle speed is 5,836 RPM at 110 m/min (360.9 SFM), with a profiling feed rate of 298 mm/min (11.7 IPM) and adjusted chip load of 0.017 mm/tooth, achieving a material removal rate of 4.02 cm³/min (0.24 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) (6 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 6 mm | 3 mm | 1× | 128 | 5 | 2.3 | 0.12 |
| Slotting (100% WOC) | 3F | 6 mm | 3 mm | 1× | 193 | 7.5 | 3.47 | 0.19 |
| Slotting (100% WOC) | 4F | 6 mm | 3 mm | 1× | 257 | 10 | 4.63 | 0.25 |
| Profiling / HEM (25% WOC) | 2F | 1.5 mm | 9 mm | 1.1547× | 198 | 7.8 | 2.67 | 0.14 |
| Profiling / HEM (25% WOC) CURRENT | 3F | 1.5 mm | 9 mm | 1.1547× | 298 | 11.7 | 4.02 | 0.22 |
| Profiling / HEM (25% WOC) | 4F | 1.5 mm | 9 mm | 1.1547× | 397 | 15.6 | 5.36 | 0.29 |
| Adaptive Clearing (10% WOC) | 2F | 0.6 mm | 12 mm | 1.6667× | 286 | 11.2 | 2.06 | 0.11 |
| Adaptive Clearing (10% WOC) | 3F | 0.6 mm | 12 mm | 1.6667× | 429 | 16.8 | 3.09 | 0.17 |
| Adaptive Clearing (10% WOC) | 4F | 0.6 mm | 12 mm | 1.6667× | 572 | 22.4 | 4.12 | 0.22 |
Shop-Floor Machining Strategy for 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)
Work Hardening: HighHigh-Pressure Flood Coolant with Synthetic Water-Soluble Fluid
Pressure: 30 to 70 bar
Heat dissipation from the shear zone prevents thermal tempering and edge fatigue.
Chip Flow: Crisp, tight curled chips; high cutting forces generated.
Milling Direction: Always climb mill.
- In H900 condition, tool rigidity and low runout (<0.005 mm) are required to avoid chipped flutes.
- Use thick-core end mills designed for hardened steels (4-5 flutes).
- Trochoidal / dynamic milling with light radial engagement (6-10%) increases tool life by 300%.
Frequently Asked CNC Questions (17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) / 6 mm)
What is the recommended RPM for milling 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) with a 6 mm end mill?
What table feed rate and chip load should I program for 6 mm in 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)?
Recent Calculations
No recent calculations saved yet.