304 Austenitic Stainless Steel (18/8) — 1" (1.000 in) 3-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 304 Austenitic Stainless Steel (18/8) with a 1" (1.000 in) 3-flute TiAlN carbide end mill, the recommended spindle speed is 1,754 RPM at 140 m/min (459.3 SFM), with a profiling feed rate of 323 mm/min (12.7 IPM) and adjusted chip load of 0.0614 mm/tooth, achieving a material removal rate of 78.15 cm³/min (4.76 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math304 Austenitic Stainless Steel (18/8) (1" (1.000 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 25.4 mm | 12.7 mm | 1× | 140 | 5.5 | 45.16 | 2.07 |
| Slotting (100% WOC) | 3F | 25.4 mm | 12.7 mm | 1× | 210 | 8.3 | 67.74 | 3.1 |
| Slotting (100% WOC) | 4F | 25.4 mm | 12.7 mm | 1× | 280 | 11 | 90.32 | 4.14 |
| Profiling / HEM (25% WOC) | 2F | 6.35 mm | 38.1 mm | 1.1547× | 215 | 8.5 | 52.02 | 2.38 |
| Profiling / HEM (25% WOC) CURRENT | 3F | 6.35 mm | 38.1 mm | 1.1547× | 323 | 12.7 | 78.15 | 3.58 |
| Profiling / HEM (25% WOC) | 4F | 6.35 mm | 38.1 mm | 1.1547× | 431 | 17 | 104.27 | 4.78 |
| Adaptive Clearing (10% WOC) | 2F | 2.54 mm | 50.8 mm | 1.6667× | 311 | 12.2 | 40.13 | 1.84 |
| Adaptive Clearing (10% WOC) | 3F | 2.54 mm | 50.8 mm | 1.6667× | 467 | 18.4 | 60.26 | 2.76 |
| Adaptive Clearing (10% WOC) | 4F | 2.54 mm | 50.8 mm | 1.6667× | 622 | 24.5 | 80.26 | 3.68 |
Shop-Floor Machining Strategy for 304 Austenitic Stainless Steel (18/8)
Work Hardening: EXTREMEHigh-Pressure Flood Coolant (10-12% Oil Concentration)
Pressure: 20 to 70 bar through-spindle preferred
Abundant coolant is required to carry away intense heat. Poor thermal conductivity means heat stays in the cut zone.
Chip Flow: Tough, stringy, work-hardened chips. Chip clearance is paramount.
Milling Direction: MANDATORY climb milling. Conventional milling rubs before shearing and work-hardens the surface to 45+ HRC.
- NEVER DWELL OR RUB: Maintain positive feed per tooth at all times. If the cutter rubs, the workpiece work-hardens instantly.
- Use unequal helix angle (variable helix) 4-flute end mills to damp out chatter harmonics.
- AlTiN or multi-layer nano-coatings provide critical barrier against built-up edge and notch wear.
Frequently Asked CNC Questions (304 Austenitic Stainless Steel (18/8) / 1" (1.000 in))
What is the recommended RPM for milling 304 Austenitic Stainless Steel (18/8) with a 1" (1.000 in) end mill?
What table feed rate and chip load should I program for 1" (1.000 in) in 304 Austenitic Stainless Steel (18/8)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 304 Austenitic Stainless Steel (18/8)?
Recent Calculations
No recent calculations saved yet.