Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

304 Austenitic Stainless Steel (18/8) — 1" (1.000 in) 4-Flute Speeds & Feeds

ISO Group M 180 HB / 88 HRB

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
1,754 RPM
Surface Speed: 140 m/min (459.3 SFM)
Table Feed Rate F = RPM·z·fz
431 mm/min
17 IPM
Plunge/Ramp Rate: 151 mm/min
Adjusted Chip Load CTF: 1.1547×
0.0614 mm/t
0.00242 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
104.27 cm³/min
6.38 in³/min
Power Required: 4.78 kW (6.41 HP)
Direct CNC Machining Solution

For milling 304 Austenitic Stainless Steel (18/8) with a 1" (1.000 in) 4-flute TiAlN carbide end mill, the recommended spindle speed is 1,754 RPM at 140 m/min (459.3 SFM), with a profiling feed rate of 431 mm/min (17 IPM) and adjusted chip load of 0.0614 mm/tooth, achieving a material removal rate of 104.27 cm³/min (6.38 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
304 Austenitic Stainless Steel (18/8) Stock CLIMB D = 25.4 mm (1") ae = 6.35 mm ap = 38.1 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1547×
Spindle Torque 20.8 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (140 × 1000) / (π × 25.4) = 1,754 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 6.35/25.4 = 0.25 → CTF = 1.1547×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0532 mm × 1.1547 = 0.0614 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 1,754 × 4 × 0.0614 = 431 mm/min (17 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (38.1 × 6.35 × 431) / 1000 = 104.27 cm³/min (6.38 in³/min)
Specific Cutting Force (kc) for 304 Austenitic Stainless Steel (18/8): 2200 N/mm². Spindle drive efficiency η = 0.80.

304 Austenitic Stainless Steel (18/8) (1" (1.000 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 1" (1.000 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 25.4 mm 12.7 mm 1× 140 5.5 45.16 2.07
Slotting (100% WOC) 3F 25.4 mm 12.7 mm 1× 210 8.3 67.74 3.1
Slotting (100% WOC) 4F 25.4 mm 12.7 mm 1× 280 11 90.32 4.14
Profiling / HEM (25% WOC) 2F 6.35 mm 38.1 mm 1.1547× 215 8.5 52.02 2.38
Profiling / HEM (25% WOC) 3F 6.35 mm 38.1 mm 1.1547× 323 12.7 78.15 3.58
Profiling / HEM (25% WOC) CURRENT 4F 6.35 mm 38.1 mm 1.1547× 431 17 104.27 4.78
Adaptive Clearing (10% WOC) 2F 2.54 mm 50.8 mm 1.6667× 311 12.2 40.13 1.84
Adaptive Clearing (10% WOC) 3F 2.54 mm 50.8 mm 1.6667× 467 18.4 60.26 2.76
Adaptive Clearing (10% WOC) 4F 2.54 mm 50.8 mm 1.6667× 622 24.5 80.26 3.68

Shop-Floor Machining Strategy for 304 Austenitic Stainless Steel (18/8)

Work Hardening: EXTREME
Coolant & Lubrication Protocol

High-Pressure Flood Coolant (10-12% Oil Concentration)

Pressure: 20 to 70 bar through-spindle preferred

Abundant coolant is required to carry away intense heat. Poor thermal conductivity means heat stays in the cut zone.

Chip Evacuation & Tool Path Guidance

Chip Flow: Tough, stringy, work-hardened chips. Chip clearance is paramount.

Milling Direction: MANDATORY climb milling. Conventional milling rubs before shearing and work-hardens the surface to 45+ HRC.

Expert Machinist Tips:
  • NEVER DWELL OR RUB: Maintain positive feed per tooth at all times. If the cutter rubs, the workpiece work-hardens instantly.
  • Use unequal helix angle (variable helix) 4-flute end mills to damp out chatter harmonics.
  • AlTiN or multi-layer nano-coatings provide critical barrier against built-up edge and notch wear.

Frequently Asked CNC Questions (304 Austenitic Stainless Steel (18/8) / 1" (1.000 in))

What is the recommended RPM for milling 304 Austenitic Stainless Steel (18/8) with a 1" (1.000 in) end mill?
For a 1" (1.000 in) (25.4 mm) TiAlN coated carbide end mill in 304 Austenitic Stainless Steel (18/8), the baseline surface cutting speed is 140 m/min (459.3 SFM), which translates to a calculated spindle speed of 1,754 RPM. If using uncoated carbide, reduce surface speed to 115 m/min (380 SFM / 1441 RPM). For HSS cutters, speed must be restricted to 20 m/min (251 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 1" (1.000 in) in 304 Austenitic Stainless Steel (18/8)?
At 1,754 RPM with a 4-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0614 mm/tooth (0.00242"/tooth) after applying a radial chip thinning factor (CTF) of 1.1547×. This yields a table feed rate of 431 mm/min (17 IPM). Ramping or plunging into material should be limited to 35% of table feed (151 mm/min / 5.9 IPM) at an entry ramp angle of 1.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 6.35 mm), the Chip Thinning Factor is 1.1547×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 304 Austenitic Stainless Steel (18/8)?
High-Pressure Flood Coolant (10-12% Oil Concentration). Pressure specification: 20 to 70 bar through-spindle preferred. Engineering rationale: Abundant coolant is required to carry away intense heat. Poor thermal conductivity means heat stays in the cut zone.