304 Austenitic Stainless Steel (18/8) — 20 mm 4-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 304 Austenitic Stainless Steel (18/8) with a 20 mm 4-flute TiAlN carbide end mill, the recommended spindle speed is 2,228 RPM at 140 m/min (459.3 SFM), with a profiling feed rate of 452 mm/min (17.8 IPM) and adjusted chip load of 0.0507 mm/tooth, achieving a material removal rate of 67.8 cm³/min (4.14 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math304 Austenitic Stainless Steel (18/8) (20 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 20 mm | 10 mm | 1× | 147 | 5.8 | 29.4 | 1.35 |
| Slotting (100% WOC) | 3F | 20 mm | 10 mm | 1× | 221 | 8.7 | 44.2 | 2.03 |
| Slotting (100% WOC) | 4F | 20 mm | 10 mm | 1× | 294 | 11.6 | 58.8 | 2.69 |
| Profiling / HEM (25% WOC) | 2F | 5 mm | 30 mm | 1.1547× | 226 | 8.9 | 33.9 | 1.55 |
| Profiling / HEM (25% WOC) | 3F | 5 mm | 30 mm | 1.1547× | 339 | 13.4 | 50.85 | 2.33 |
| Profiling / HEM (25% WOC) CURRENT | 4F | 5 mm | 30 mm | 1.1547× | 452 | 17.8 | 67.8 | 3.11 |
| Adaptive Clearing (10% WOC) | 2F | 2 mm | 40 mm | 1.6667× | 326 | 12.8 | 26.08 | 1.2 |
| Adaptive Clearing (10% WOC) | 3F | 2 mm | 40 mm | 1.6667× | 489 | 19.2 | 39.12 | 1.79 |
| Adaptive Clearing (10% WOC) | 4F | 2 mm | 40 mm | 1.6667× | 652 | 25.7 | 52.16 | 2.39 |
Shop-Floor Machining Strategy for 304 Austenitic Stainless Steel (18/8)
Work Hardening: EXTREMEHigh-Pressure Flood Coolant (10-12% Oil Concentration)
Pressure: 20 to 70 bar through-spindle preferred
Abundant coolant is required to carry away intense heat. Poor thermal conductivity means heat stays in the cut zone.
Chip Flow: Tough, stringy, work-hardened chips. Chip clearance is paramount.
Milling Direction: MANDATORY climb milling. Conventional milling rubs before shearing and work-hardens the surface to 45+ HRC.
- NEVER DWELL OR RUB: Maintain positive feed per tooth at all times. If the cutter rubs, the workpiece work-hardens instantly.
- Use unequal helix angle (variable helix) 4-flute end mills to damp out chatter harmonics.
- AlTiN or multi-layer nano-coatings provide critical barrier against built-up edge and notch wear.
Frequently Asked CNC Questions (304 Austenitic Stainless Steel (18/8) / 20 mm)
What is the recommended RPM for milling 304 Austenitic Stainless Steel (18/8) with a 20 mm end mill?
What table feed rate and chip load should I program for 20 mm in 304 Austenitic Stainless Steel (18/8)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 304 Austenitic Stainless Steel (18/8)?
Recent Calculations
No recent calculations saved yet.