Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

304 Austenitic Stainless Steel (18/8) — 5/8" (0.625 in) 2-Flute Speeds & Feeds

ISO Group M 180 HB / 88 HRB

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
2,807 RPM
Surface Speed: 140 m/min (459.3 SFM)
Table Feed Rate F = RPM·z·fz
236 mm/min
9.3 IPM
Plunge/Ramp Rate: 83 mm/min
Adjusted Chip Load CTF: 1.1546×
0.0421 mm/t
0.00166 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
22.31 cm³/min
1.36 in³/min
Power Required: 1.02 kW (1.37 HP)
Direct CNC Machining Solution

For milling 304 Austenitic Stainless Steel (18/8) with a 5/8" (0.625 in) 2-flute TiAlN carbide end mill, the recommended spindle speed is 2,807 RPM at 140 m/min (459.3 SFM), with a profiling feed rate of 236 mm/min (9.3 IPM) and adjusted chip load of 0.0421 mm/tooth, achieving a material removal rate of 22.31 cm³/min (1.36 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
304 Austenitic Stainless Steel (18/8) Stock CLIMB D = 15.875 mm (0.625") ae = 3.97 mm ap = 23.81 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1546×
Spindle Torque 2.79 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (140 × 1000) / (π × 15.875) = 2,807 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 3.97/15.875 = 0.25 → CTF = 1.1546×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0365 mm × 1.1546 = 0.0421 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 2,807 × 2 × 0.0421 = 236 mm/min (9.3 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (23.81 × 3.97 × 236) / 1000 = 22.31 cm³/min (1.36 in³/min)
Specific Cutting Force (kc) for 304 Austenitic Stainless Steel (18/8): 2200 N/mm². Spindle drive efficiency η = 0.80.

304 Austenitic Stainless Steel (18/8) (5/8" (0.625 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 5/8" (0.625 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 15.88 mm 7.94 mm 1× 154 6.1 19.42 0.89
Slotting (100% WOC) 3F 15.88 mm 7.94 mm 1× 231 9.1 29.13 1.34
Slotting (100% WOC) 4F 15.88 mm 7.94 mm 1× 308 12.1 38.83 1.78
Profiling / HEM (25% WOC) CURRENT 2F 3.97 mm 23.81 mm 1.1546× 236 9.3 22.31 1.02
Profiling / HEM (25% WOC) 3F 3.97 mm 23.81 mm 1.1546× 355 14 33.56 1.54
Profiling / HEM (25% WOC) 4F 3.97 mm 23.81 mm 1.1546× 473 18.6 44.71 2.05
Adaptive Clearing (10% WOC) 2F 1.59 mm 31.75 mm 1.6655× 341 13.4 17.21 0.79
Adaptive Clearing (10% WOC) 3F 1.59 mm 31.75 mm 1.6655× 512 20.1 25.85 1.18
Adaptive Clearing (10% WOC) 4F 1.59 mm 31.75 mm 1.6655× 683 26.8 34.48 1.58

Shop-Floor Machining Strategy for 304 Austenitic Stainless Steel (18/8)

Work Hardening: EXTREME
Coolant & Lubrication Protocol

High-Pressure Flood Coolant (10-12% Oil Concentration)

Pressure: 20 to 70 bar through-spindle preferred

Abundant coolant is required to carry away intense heat. Poor thermal conductivity means heat stays in the cut zone.

Chip Evacuation & Tool Path Guidance

Chip Flow: Tough, stringy, work-hardened chips. Chip clearance is paramount.

Milling Direction: MANDATORY climb milling. Conventional milling rubs before shearing and work-hardens the surface to 45+ HRC.

Expert Machinist Tips:
  • NEVER DWELL OR RUB: Maintain positive feed per tooth at all times. If the cutter rubs, the workpiece work-hardens instantly.
  • Use unequal helix angle (variable helix) 4-flute end mills to damp out chatter harmonics.
  • AlTiN or multi-layer nano-coatings provide critical barrier against built-up edge and notch wear.

Frequently Asked CNC Questions (304 Austenitic Stainless Steel (18/8) / 5/8" (0.625 in))

What is the recommended RPM for milling 304 Austenitic Stainless Steel (18/8) with a 5/8" (0.625 in) end mill?
For a 5/8" (0.625 in) (15.875 mm) TiAlN coated carbide end mill in 304 Austenitic Stainless Steel (18/8), the baseline surface cutting speed is 140 m/min (459.3 SFM), which translates to a calculated spindle speed of 2,807 RPM. If using uncoated carbide, reduce surface speed to 115 m/min (380 SFM / 2306 RPM). For HSS cutters, speed must be restricted to 20 m/min (401 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 5/8" (0.625 in) in 304 Austenitic Stainless Steel (18/8)?
At 2,807 RPM with a 2-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0421 mm/tooth (0.00166"/tooth) after applying a radial chip thinning factor (CTF) of 1.1546×. This yields a table feed rate of 236 mm/min (9.3 IPM). Ramping or plunging into material should be limited to 35% of table feed (83 mm/min / 3.3 IPM) at an entry ramp angle of 3°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 3.97 mm), the Chip Thinning Factor is 1.1546×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 304 Austenitic Stainless Steel (18/8)?
High-Pressure Flood Coolant (10-12% Oil Concentration). Pressure specification: 20 to 70 bar through-spindle preferred. Engineering rationale: Abundant coolant is required to carry away intense heat. Poor thermal conductivity means heat stays in the cut zone.