Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

304 Austenitic Stainless Steel (18/8) — 3/4" (0.750 in) 2-Flute Speeds & Feeds

ISO Group M 180 HB / 88 HRB

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
2,339 RPM
Surface Speed: 140 m/min (459.3 SFM)
Table Feed Rate F = RPM·z·fz
229 mm/min
9 IPM
Plunge/Ramp Rate: 80 mm/min
Adjusted Chip Load CTF: 1.1549×
0.0489 mm/t
0.00193 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
31.15 cm³/min
1.9 in³/min
Power Required: 1.43 kW (1.91 HP)
Direct CNC Machining Solution

For milling 304 Austenitic Stainless Steel (18/8) with a 3/4" (0.750 in) 2-flute TiAlN carbide end mill, the recommended spindle speed is 2,339 RPM at 140 m/min (459.3 SFM), with a profiling feed rate of 229 mm/min (9 IPM) and adjusted chip load of 0.0489 mm/tooth, achieving a material removal rate of 31.15 cm³/min (1.9 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
304 Austenitic Stainless Steel (18/8) Stock CLIMB D = 19.05 mm (0.75") ae = 4.76 mm ap = 28.58 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1549×
Spindle Torque 4.65 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (140 × 1000) / (π × 19.05) = 2,339 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 4.76/19.05 = 0.25 → CTF = 1.1549×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0423 mm × 1.1549 = 0.0489 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 2,339 × 2 × 0.0489 = 229 mm/min (9 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (28.58 × 4.76 × 229) / 1000 = 31.15 cm³/min (1.9 in³/min)
Specific Cutting Force (kc) for 304 Austenitic Stainless Steel (18/8): 2200 N/mm². Spindle drive efficiency η = 0.80.

304 Austenitic Stainless Steel (18/8) (3/4" (0.750 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 3/4" (0.750 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 19.05 mm 9.53 mm 1× 148 5.8 26.87 1.23
Slotting (100% WOC) 3F 19.05 mm 9.53 mm 1× 222 8.8 40.3 1.85
Slotting (100% WOC) 4F 19.05 mm 9.53 mm 1× 297 11.7 53.92 2.47
Profiling / HEM (25% WOC) CURRENT 2F 4.76 mm 28.58 mm 1.1549× 229 9 31.15 1.43
Profiling / HEM (25% WOC) 3F 4.76 mm 28.58 mm 1.1549× 343 13.5 46.66 2.14
Profiling / HEM (25% WOC) 4F 4.76 mm 28.58 mm 1.1549× 458 18.1 62.31 2.86
Adaptive Clearing (10% WOC) 2F 1.91 mm 38.1 mm 1.6647× 329 13 23.94 1.1
Adaptive Clearing (10% WOC) 3F 1.91 mm 38.1 mm 1.6647× 494 19.4 35.95 1.65
Adaptive Clearing (10% WOC) 4F 1.91 mm 38.1 mm 1.6647× 659 25.9 47.96 2.2

Shop-Floor Machining Strategy for 304 Austenitic Stainless Steel (18/8)

Work Hardening: EXTREME
Coolant & Lubrication Protocol

High-Pressure Flood Coolant (10-12% Oil Concentration)

Pressure: 20 to 70 bar through-spindle preferred

Abundant coolant is required to carry away intense heat. Poor thermal conductivity means heat stays in the cut zone.

Chip Evacuation & Tool Path Guidance

Chip Flow: Tough, stringy, work-hardened chips. Chip clearance is paramount.

Milling Direction: MANDATORY climb milling. Conventional milling rubs before shearing and work-hardens the surface to 45+ HRC.

Expert Machinist Tips:
  • NEVER DWELL OR RUB: Maintain positive feed per tooth at all times. If the cutter rubs, the workpiece work-hardens instantly.
  • Use unequal helix angle (variable helix) 4-flute end mills to damp out chatter harmonics.
  • AlTiN or multi-layer nano-coatings provide critical barrier against built-up edge and notch wear.

Frequently Asked CNC Questions (304 Austenitic Stainless Steel (18/8) / 3/4" (0.750 in))

What is the recommended RPM for milling 304 Austenitic Stainless Steel (18/8) with a 3/4" (0.750 in) end mill?
For a 3/4" (0.750 in) (19.05 mm) TiAlN coated carbide end mill in 304 Austenitic Stainless Steel (18/8), the baseline surface cutting speed is 140 m/min (459.3 SFM), which translates to a calculated spindle speed of 2,339 RPM. If using uncoated carbide, reduce surface speed to 115 m/min (380 SFM / 1922 RPM). For HSS cutters, speed must be restricted to 20 m/min (334 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 3/4" (0.750 in) in 304 Austenitic Stainless Steel (18/8)?
At 2,339 RPM with a 2-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0489 mm/tooth (0.00193"/tooth) after applying a radial chip thinning factor (CTF) of 1.1549×. This yields a table feed rate of 229 mm/min (9 IPM). Ramping or plunging into material should be limited to 35% of table feed (80 mm/min / 3.1 IPM) at an entry ramp angle of 3°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 4.76 mm), the Chip Thinning Factor is 1.1549×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 304 Austenitic Stainless Steel (18/8)?
High-Pressure Flood Coolant (10-12% Oil Concentration). Pressure specification: 20 to 70 bar through-spindle preferred. Engineering rationale: Abundant coolant is required to carry away intense heat. Poor thermal conductivity means heat stays in the cut zone.