Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC) — 5/8" (0.625 in) 2-Flute Speeds & Feeds

ISO Group P 280-320 HB / 28-32 HRC

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
3,810 RPM
Surface Speed: 190 m/min (623.4 SFM)
Table Feed Rate F = RPM·z·fz
386 mm/min
15.2 IPM
Plunge/Ramp Rate: 135 mm/min
Adjusted Chip Load CTF: 1.1546×
0.0506 mm/t
0.00199 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
36.49 cm³/min
2.23 in³/min
Power Required: 1.6 kW (2.14 HP)
Direct CNC Machining Solution

For milling 4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC) with a 5/8" (0.625 in) 2-flute TiAlN carbide end mill, the recommended spindle speed is 3,810 RPM at 190 m/min (623.4 SFM), with a profiling feed rate of 386 mm/min (15.2 IPM) and adjusted chip load of 0.0506 mm/tooth, achieving a material removal rate of 36.49 cm³/min (2.23 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC) Stock CLIMB D = 15.875 mm (0.625") ae = 3.97 mm ap = 23.81 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1546×
Spindle Torque 3.21 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (190 × 1000) / (π × 15.875) = 3,810 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 3.97/15.875 = 0.25 → CTF = 1.1546×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0438 mm × 1.1546 = 0.0506 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 3,810 × 2 × 0.0506 = 386 mm/min (15.2 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (23.81 × 3.97 × 386) / 1000 = 36.49 cm³/min (2.23 in³/min)
Specific Cutting Force (kc) for 4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC): 2100 N/mm². Spindle drive efficiency η = 0.80.

4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC) (5/8" (0.625 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 5/8" (0.625 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 15.88 mm 7.94 mm 1× 251 9.9 31.65 1.38
Slotting (100% WOC) 3F 15.88 mm 7.94 mm 1× 376 14.9 47.41 2.07
Slotting (100% WOC) 4F 15.88 mm 7.94 mm 1× 501 19.8 63.17 2.76
Profiling / HEM (25% WOC) CURRENT 2F 3.97 mm 23.81 mm 1.1546× 386 15.2 36.49 1.6
Profiling / HEM (25% WOC) 3F 3.97 mm 23.81 mm 1.1546× 578 22.7 54.64 2.39
Profiling / HEM (25% WOC) 4F 3.97 mm 23.81 mm 1.1546× 771 30.3 72.88 3.19
Adaptive Clearing (10% WOC) 2F 1.59 mm 31.75 mm 1.6655× 555 21.9 28.02 1.23
Adaptive Clearing (10% WOC) 3F 1.59 mm 31.75 mm 1.6655× 833 32.8 42.05 1.84
Adaptive Clearing (10% WOC) 4F 1.59 mm 31.75 mm 1.6655× 1,111 43.7 56.09 2.45

Shop-Floor Machining Strategy for 4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC)

Work Hardening: Moderate-High
Coolant & Lubrication Protocol

Air Blast for TiAlN Coated Carbide; Flood Coolant for HSS

Pressure: 6 bar air blast or 20 bar high-pressure flood

Thermal shock from erratic coolant flow causes micro-chipping of carbide cutting edges.

Chip Evacuation & Tool Path Guidance

Chip Flow: Short curled chips form with proper feed; excellent surface finish potential.

Milling Direction: Climb milling essential to enter at thickest chip portion.

Expert Machinist Tips:
  • Pre-hardened 4140 (HT) machines cleanly with rigid setups and AlTiN or TiAlN coated tooling.
  • Use high-efficiency milling (HEM): 8-12% ae radial engagement with 1.5x-2.0x ap depth of cut.
  • Keep tool stickout as short as possible to eliminate chatter harmonics.

Frequently Asked CNC Questions (4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC) / 5/8" (0.625 in))

What is the recommended RPM for milling 4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC) with a 5/8" (0.625 in) end mill?
For a 5/8" (0.625 in) (15.875 mm) TiAlN coated carbide end mill in 4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC), the baseline surface cutting speed is 190 m/min (623.4 SFM), which translates to a calculated spindle speed of 3,810 RPM. If using uncoated carbide, reduce surface speed to 150 m/min (500 SFM / 3008 RPM). For HSS cutters, speed must be restricted to 24 m/min (481 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 5/8" (0.625 in) in 4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC)?
At 3,810 RPM with a 2-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0506 mm/tooth (0.00199"/tooth) after applying a radial chip thinning factor (CTF) of 1.1546×. This yields a table feed rate of 386 mm/min (15.2 IPM). Ramping or plunging into material should be limited to 35% of table feed (135 mm/min / 5.3 IPM) at an entry ramp angle of 3°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 3.97 mm), the Chip Thinning Factor is 1.1546×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC)?
Air Blast for TiAlN Coated Carbide; Flood Coolant for HSS. Pressure specification: 6 bar air blast or 20 bar high-pressure flood. Engineering rationale: Thermal shock from erratic coolant flow causes micro-chipping of carbide cutting edges.