304 Austenitic Stainless Steel (18/8) — 6 mm 2-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 304 Austenitic Stainless Steel (18/8) with a 6 mm 2-flute TiAlN carbide end mill, the recommended spindle speed is 7,427 RPM at 140 m/min (459.3 SFM), with a profiling feed rate of 288 mm/min (11.3 IPM) and adjusted chip load of 0.0194 mm/tooth, achieving a material removal rate of 3.89 cm³/min (0.24 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math304 Austenitic Stainless Steel (18/8) (6 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 6 mm | 3 mm | 1× | 187 | 7.4 | 3.37 | 0.15 |
| Slotting (100% WOC) | 3F | 6 mm | 3 mm | 1× | 281 | 11.1 | 5.06 | 0.23 |
| Slotting (100% WOC) | 4F | 6 mm | 3 mm | 1× | 374 | 14.9 | 6.73 | 0.31 |
| Profiling / HEM (25% WOC) CURRENT | 2F | 1.5 mm | 9 mm | 1.1547× | 288 | 11.3 | 3.89 | 0.18 |
| Profiling / HEM (25% WOC) | 3F | 1.5 mm | 9 mm | 1.1547× | 432 | 16.9 | 5.83 | 0.27 |
| Profiling / HEM (25% WOC) | 4F | 1.5 mm | 9 mm | 1.1547× | 576 | 22.6 | 7.78 | 0.36 |
| Adaptive Clearing (10% WOC) | 2F | 0.6 mm | 12 mm | 1.6667× | 416 | 16.3 | 3 | 0.14 |
| Adaptive Clearing (10% WOC) | 3F | 0.6 mm | 12 mm | 1.6667× | 624 | 24.5 | 4.49 | 0.21 |
| Adaptive Clearing (10% WOC) | 4F | 0.6 mm | 12 mm | 1.6667× | 832 | 32.7 | 5.99 | 0.27 |
Shop-Floor Machining Strategy for 304 Austenitic Stainless Steel (18/8)
Work Hardening: EXTREMEHigh-Pressure Flood Coolant (10-12% Oil Concentration)
Pressure: 20 to 70 bar through-spindle preferred
Abundant coolant is required to carry away intense heat. Poor thermal conductivity means heat stays in the cut zone.
Chip Flow: Tough, stringy, work-hardened chips. Chip clearance is paramount.
Milling Direction: MANDATORY climb milling. Conventional milling rubs before shearing and work-hardens the surface to 45+ HRC.
- NEVER DWELL OR RUB: Maintain positive feed per tooth at all times. If the cutter rubs, the workpiece work-hardens instantly.
- Use unequal helix angle (variable helix) 4-flute end mills to damp out chatter harmonics.
- AlTiN or multi-layer nano-coatings provide critical barrier against built-up edge and notch wear.
Frequently Asked CNC Questions (304 Austenitic Stainless Steel (18/8) / 6 mm)
What is the recommended RPM for milling 304 Austenitic Stainless Steel (18/8) with a 6 mm end mill?
What table feed rate and chip load should I program for 6 mm in 304 Austenitic Stainless Steel (18/8)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 304 Austenitic Stainless Steel (18/8)?
Recent Calculations
No recent calculations saved yet.