316 Marine Grade Stainless Steel (with Molybdenum) — 1/2" (0.500 in) 4-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 316 Marine Grade Stainless Steel (with Molybdenum) with a 1/2" (0.500 in) 4-flute TiAlN carbide end mill, the recommended spindle speed is 3,133 RPM at 125 m/min (410.1 SFM), with a profiling feed rate of 420 mm/min (16.5 IPM) and adjusted chip load of 0.0335 mm/tooth, achieving a material removal rate of 25.36 cm³/min (1.54 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math316 Marine Grade Stainless Steel (with Molybdenum) (1/2" (0.500 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 12.7 mm | 6.35 mm | 1× | 137 | 5.4 | 11.05 | 0.53 |
| Slotting (100% WOC) | 3F | 12.7 mm | 6.35 mm | 1× | 205 | 8.1 | 16.53 | 0.79 |
| Slotting (100% WOC) | 4F | 12.7 mm | 6.35 mm | 1× | 273 | 10.8 | 22.02 | 1.06 |
| Profiling / HEM (25% WOC) | 2F | 3.17 mm | 19.05 mm | 1.1553× | 210 | 8.3 | 12.68 | 0.61 |
| Profiling / HEM (25% WOC) | 3F | 3.17 mm | 19.05 mm | 1.1553× | 315 | 12.4 | 19.02 | 0.91 |
| Profiling / HEM (25% WOC) CURRENT | 4F | 3.17 mm | 19.05 mm | 1.1553× | 420 | 16.5 | 25.36 | 1.22 |
| Adaptive Clearing (10% WOC) | 2F | 1.27 mm | 25.4 mm | 1.6667× | 303 | 11.9 | 9.77 | 0.47 |
| Adaptive Clearing (10% WOC) | 3F | 1.27 mm | 25.4 mm | 1.6667× | 454 | 17.9 | 14.65 | 0.7 |
| Adaptive Clearing (10% WOC) | 4F | 1.27 mm | 25.4 mm | 1.6667× | 605 | 23.8 | 19.52 | 0.94 |
Shop-Floor Machining Strategy for 316 Marine Grade Stainless Steel (with Molybdenum)
Work Hardening: EXTREMEHeavy Flood Coolant with Extreme Pressure (EP) Additives
Pressure: 20 bar minimum
Molybdenum addition increases chemical and high-temp shear toughness, requiring superior lubricity.
Chip Flow: High tendency for chips to weld to cutting edges if feed pauses.
Milling Direction: Mandatory climb milling.
- Reduce SFM by 10-15% compared to 304 stainless; keep chip load firm.
- Corner chamfer or radiused cutters prevent premature notch wear on the depth-of-cut line.
- Use high-feed milling or trochoidal toolpaths to spread wear along the full flute length.
Frequently Asked CNC Questions (316 Marine Grade Stainless Steel (with Molybdenum) / 1/2" (0.500 in))
What is the recommended RPM for milling 316 Marine Grade Stainless Steel (with Molybdenum) with a 1/2" (0.500 in) end mill?
What table feed rate and chip load should I program for 1/2" (0.500 in) in 316 Marine Grade Stainless Steel (with Molybdenum)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 316 Marine Grade Stainless Steel (with Molybdenum)?
Recent Calculations
No recent calculations saved yet.