Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

7075-T6 Aerospace Aluminum — 1/2" (0.500 in) 4-Flute Speeds & Feeds

ISO Group N 150 HB / 87 HRB

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
14,537 RPM
Surface Speed: 580 m/min (1902.9 SFM)
Table Feed Rate F = RPM·z·fz
3,594 mm/min
141.3 IPM
Plunge/Ramp Rate: 1258 mm/min
Adjusted Chip Load CTF: 1.1553×
0.0618 mm/t
0.00243 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
217.04 cm³/min
13.23 in³/min
Power Required: 3.84 kW (5.15 HP)
Direct CNC Machining Solution

For milling 7075-T6 Aerospace Aluminum with a 1/2" (0.500 in) 4-flute TiAlN carbide end mill, the recommended spindle speed is 14,537 RPM at 580 m/min (1902.9 SFM), with a profiling feed rate of 3,594 mm/min (141.3 IPM) and adjusted chip load of 0.0618 mm/tooth, achieving a material removal rate of 217.04 cm³/min (13.23 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
7075-T6 Aerospace Aluminum Stock CLIMB D = 12.7 mm (0.5") ae = 3.17 mm ap = 19.05 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1553×
Spindle Torque 2.02 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (580 × 1000) / (π × 12.7) = 14,537 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 3.17/12.7 = 0.25 → CTF = 1.1553×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0535 mm × 1.1553 = 0.0618 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 14,537 × 4 × 0.0618 = 3,594 mm/min (141.3 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (19.05 × 3.17 × 3594) / 1000 = 217.04 cm³/min (13.23 in³/min)
Specific Cutting Force (kc) for 7075-T6 Aerospace Aluminum: 850 N/mm². Spindle drive efficiency η = 0.80.

7075-T6 Aerospace Aluminum (1/2" (0.500 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 1/2" (0.500 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 12.7 mm 6.35 mm 1× 1,166 45.9 94.03 1.67
Slotting (100% WOC) 3F 12.7 mm 6.35 mm 1× 1,749 68.9 141.05 2.5
Slotting (100% WOC) 4F 12.7 mm 6.35 mm 1× 2,332 91.9 188.06 3.33
Profiling / HEM (25% WOC) 2F 3.17 mm 19.05 mm 1.1553× 1,797 70.6 108.52 1.92
Profiling / HEM (25% WOC) 3F 3.17 mm 19.05 mm 1.1553× 2,695 106 162.75 2.88
Profiling / HEM (25% WOC) CURRENT 4F 3.17 mm 19.05 mm 1.1553× 3,594 141.3 217.04 3.84
Adaptive Clearing (10% WOC) 2F 1.27 mm 25.4 mm 1.6667× 2,593 102 83.64 1.48
Adaptive Clearing (10% WOC) 3F 1.27 mm 25.4 mm 1.6667× 3,890 153.1 125.48 2.22
Adaptive Clearing (10% WOC) 4F 1.27 mm 25.4 mm 1.6667× 5,187 204.1 167.32 2.96

Shop-Floor Machining Strategy for 7075-T6 Aerospace Aluminum

Work Hardening: Low
Coolant & Lubrication Protocol

Flood Coolant with 8-10% Synthetic Soluble Oil Concentration

Pressure: Standard flood (5 bar minimum)

Zinc-alloyed aluminum chips break cleaner than 6061, with superior surface finish.

Chip Evacuation & Tool Path Guidance

Chip Flow: Excellent short crisp chips compared to 6061. Can run 3-flute tools at aggressive feeds.

Milling Direction: Climb milling gives mirror surface finishes.

Expert Machinist Tips:
  • High zinc content gives higher tensile strength; chips shear off crisply.
  • Maintain tool rigidity; deflection causes dimensional drift on tight aerospace tolerances.
  • Ideal candidate for High-Speed Machining (HSM) with high axial depth and light radial stepover.

Frequently Asked CNC Questions (7075-T6 Aerospace Aluminum / 1/2" (0.500 in))

What is the recommended RPM for milling 7075-T6 Aerospace Aluminum with a 1/2" (0.500 in) end mill?
For a 1/2" (0.500 in) (12.7 mm) TiAlN coated carbide end mill in 7075-T6 Aerospace Aluminum, the baseline surface cutting speed is 580 m/min (1902.9 SFM), which translates to a calculated spindle speed of 14,537 RPM. If using uncoated carbide, reduce surface speed to 480 m/min (1600 SFM / 12031 RPM). For HSS cutters, speed must be restricted to 100 m/min (2506 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 1/2" (0.500 in) in 7075-T6 Aerospace Aluminum?
At 14,537 RPM with a 4-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0618 mm/tooth (0.00243"/tooth) after applying a radial chip thinning factor (CTF) of 1.1553×. This yields a table feed rate of 3594 mm/min (141.3 IPM). Ramping or plunging into material should be limited to 35% of table feed (1258 mm/min / 49.5 IPM) at an entry ramp angle of 1.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 3.17 mm), the Chip Thinning Factor is 1.1553×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 7075-T6 Aerospace Aluminum?
Flood Coolant with 8-10% Synthetic Soluble Oil Concentration. Pressure specification: Standard flood (5 bar minimum). Engineering rationale: Zinc-alloyed aluminum chips break cleaner than 6061, with superior surface finish.