6061-T6 Aluminum — 1/2" (0.500 in) 4-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 6061-T6 Aluminum with a 1/2" (0.500 in) 4-flute TiAlN carbide end mill, the recommended spindle speed is 16,291 RPM at 650 m/min (2132.5 SFM), with a profiling feed rate of 4,314 mm/min (170.1 IPM) and adjusted chip load of 0.0662 mm/tooth, achieving a material removal rate of 260.52 cm³/min (15.92 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math6061-T6 Aluminum (1/2" (0.500 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 12.7 mm | 6.35 mm | 1× | 1,401 | 55.1 | 112.98 | 1.65 |
| Slotting (100% WOC) | 3F | 12.7 mm | 6.35 mm | 1× | 2,102 | 82.6 | 169.52 | 2.47 |
| Slotting (100% WOC) | 4F | 12.7 mm | 6.35 mm | 1× | 2,802 | 110.1 | 225.97 | 3.3 |
| Profiling / HEM (25% WOC) | 2F | 3.17 mm | 19.05 mm | 1.1553× | 2,157 | 85 | 130.26 | 1.9 |
| Profiling / HEM (25% WOC) | 3F | 3.17 mm | 19.05 mm | 1.1553× | 3,235 | 127.6 | 195.36 | 2.85 |
| Profiling / HEM (25% WOC) CURRENT | 4F | 3.17 mm | 19.05 mm | 1.1553× | 4,314 | 170.1 | 260.52 | 3.8 |
| Adaptive Clearing (10% WOC) | 2F | 1.27 mm | 25.4 mm | 1.6667× | 3,112 | 122.5 | 100.39 | 1.46 |
| Adaptive Clearing (10% WOC) | 3F | 1.27 mm | 25.4 mm | 1.6667× | 4,667 | 183.8 | 150.55 | 2.2 |
| Adaptive Clearing (10% WOC) | 4F | 1.27 mm | 25.4 mm | 1.6667× | 6,223 | 245 | 200.74 | 2.93 |
Shop-Floor Machining Strategy for 6061-T6 Aluminum
Work Hardening: LowHigh-Pressure Flood Coolant or MQL Air Blast with Alcohol/Oil Mist
Pressure: Flood at 5-10 bar; Through-Spindle 20 bar
Lubricity is critical. Dry cutting risks instantaneous aluminum welding to tool flutes and catastrophic cutter snap.
Chip Flow: Use polished flutes (ZrN or DLC coating) and 2 or 3 flutes to prevent chip re-cutting.
Milling Direction: Always climb mill. Conventional milling causes built-up edge on the tool face.
- Max spindle speed is usually preferred; feed fast to maintain minimum chip thickness (>0.02 mm) to prevent rubbing.
- In deep pocketing, utilize high pressure air blast to blast chips out of the cavity.
- For high-speed trochoidal slotting, use 10-15% radial stepover (ae) at 2.0x-3.0x axial depth (ap).
Frequently Asked CNC Questions (6061-T6 Aluminum / 1/2" (0.500 in))
What is the recommended RPM for milling 6061-T6 Aluminum with a 1/2" (0.500 in) end mill?
What table feed rate and chip load should I program for 1/2" (0.500 in) in 6061-T6 Aluminum?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 6061-T6 Aluminum?
Recent Calculations
No recent calculations saved yet.