Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

316 Marine Grade Stainless Steel (with Molybdenum) — 3/16" (0.1875 in) 2-Flute Speeds & Feeds

ISO Group M 185 HB / 90 HRB

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
8,355 RPM
Surface Speed: 125 m/min (410.1 SFM)
Table Feed Rate F = RPM·z·fz
254 mm/min
10 IPM
Plunge/Ramp Rate: 89 mm/min
Adjusted Chip Load CTF: 1.1549×
0.0152 mm/t
0.0006 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
2.16 cm³/min
0.13 in³/min
Power Required: 0.1 kW (0.14 HP)
Direct CNC Machining Solution

For milling 316 Marine Grade Stainless Steel (with Molybdenum) with a 3/16" (0.1875 in) 2-flute TiAlN carbide end mill, the recommended spindle speed is 8,355 RPM at 125 m/min (410.1 SFM), with a profiling feed rate of 254 mm/min (10 IPM) and adjusted chip load of 0.0152 mm/tooth, achieving a material removal rate of 2.16 cm³/min (0.13 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
316 Marine Grade Stainless Steel (with Molybdenum) Stock CLIMB D = 4.762 mm (0.1875") ae = 1.19 mm ap = 7.14 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1549×
Spindle Torque 0.09 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (125 × 1000) / (π × 4.762) = 8,355 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 1.19/4.762 = 0.25 → CTF = 1.1549×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0132 mm × 1.1549 = 0.0152 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 8,355 × 2 × 0.0152 = 254 mm/min (10 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (7.14 × 1.19 × 254) / 1000 = 2.16 cm³/min (0.13 in³/min)
Specific Cutting Force (kc) for 316 Marine Grade Stainless Steel (with Molybdenum): 2300 N/mm². Spindle drive efficiency η = 0.80.

316 Marine Grade Stainless Steel (with Molybdenum) (3/16" (0.1875 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 3/16" (0.1875 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 4.76 mm 2.38 mm 1× 165 6.5 1.87 0.09
Slotting (100% WOC) 3F 4.76 mm 2.38 mm 1× 248 9.8 2.81 0.13
Slotting (100% WOC) 4F 4.76 mm 2.38 mm 1× 331 13 3.75 0.18
Profiling / HEM (25% WOC) CURRENT 2F 1.19 mm 7.14 mm 1.1549× 254 10 2.16 0.1
Profiling / HEM (25% WOC) 3F 1.19 mm 7.14 mm 1.1549× 381 15 3.24 0.16
Profiling / HEM (25% WOC) 4F 1.19 mm 7.14 mm 1.1549× 508 20.1 4.32 0.21
Adaptive Clearing (10% WOC) 2F 0.48 mm 9.52 mm 1.6608× 366 14.4 1.67 0.08
Adaptive Clearing (10% WOC) 3F 0.48 mm 9.52 mm 1.6608× 549 21.6 2.51 0.12
Adaptive Clearing (10% WOC) 4F 0.48 mm 9.52 mm 1.6608× 732 28.7 3.34 0.16

Shop-Floor Machining Strategy for 316 Marine Grade Stainless Steel (with Molybdenum)

Work Hardening: EXTREME
Coolant & Lubrication Protocol

Heavy Flood Coolant with Extreme Pressure (EP) Additives

Pressure: 20 bar minimum

Molybdenum addition increases chemical and high-temp shear toughness, requiring superior lubricity.

Chip Evacuation & Tool Path Guidance

Chip Flow: High tendency for chips to weld to cutting edges if feed pauses.

Milling Direction: Mandatory climb milling.

Expert Machinist Tips:
  • Reduce SFM by 10-15% compared to 304 stainless; keep chip load firm.
  • Corner chamfer or radiused cutters prevent premature notch wear on the depth-of-cut line.
  • Use high-feed milling or trochoidal toolpaths to spread wear along the full flute length.

Frequently Asked CNC Questions (316 Marine Grade Stainless Steel (with Molybdenum) / 3/16" (0.1875 in))

What is the recommended RPM for milling 316 Marine Grade Stainless Steel (with Molybdenum) with a 3/16" (0.1875 in) end mill?
For a 3/16" (0.1875 in) (4.762 mm) TiAlN coated carbide end mill in 316 Marine Grade Stainless Steel (with Molybdenum), the baseline surface cutting speed is 125 m/min (410.1 SFM), which translates to a calculated spindle speed of 8,355 RPM. If using uncoated carbide, reduce surface speed to 100 m/min (330 SFM / 6684 RPM). For HSS cutters, speed must be restricted to 18 m/min (1203 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 3/16" (0.1875 in) in 316 Marine Grade Stainless Steel (with Molybdenum)?
At 8,355 RPM with a 2-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0152 mm/tooth (0.0006"/tooth) after applying a radial chip thinning factor (CTF) of 1.1549×. This yields a table feed rate of 254 mm/min (10 IPM). Ramping or plunging into material should be limited to 35% of table feed (89 mm/min / 3.5 IPM) at an entry ramp angle of 3°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 1.19 mm), the Chip Thinning Factor is 1.1549×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 316 Marine Grade Stainless Steel (with Molybdenum)?
Heavy Flood Coolant with Extreme Pressure (EP) Additives. Pressure specification: 20 bar minimum. Engineering rationale: Molybdenum addition increases chemical and high-temp shear toughness, requiring superior lubricity.