Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC) — 3/8" (0.375 in) 4-Flute Speeds & Feeds

ISO Group P 280-320 HB / 28-32 HRC

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
6,349 RPM
Surface Speed: 190 m/min (623.4 SFM)
Table Feed Rate F = RPM·z·fz
853 mm/min
33.5 IPM
Plunge/Ramp Rate: 299 mm/min
Adjusted Chip Load CTF: 1.1549×
0.0336 mm/t
0.00132 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
29.01 cm³/min
1.77 in³/min
Power Required: 1.27 kW (1.7 HP)
Direct CNC Machining Solution

For milling 4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC) with a 3/8" (0.375 in) 4-flute TiAlN carbide end mill, the recommended spindle speed is 6,349 RPM at 190 m/min (623.4 SFM), with a profiling feed rate of 853 mm/min (33.5 IPM) and adjusted chip load of 0.0336 mm/tooth, achieving a material removal rate of 29.01 cm³/min (1.77 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC) Stock CLIMB D = 9.525 mm (0.375") ae = 2.38 mm ap = 14.29 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1549×
Spindle Torque 1.53 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (190 × 1000) / (π × 9.525) = 6,349 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 2.38/9.525 = 0.25 → CTF = 1.1549×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0291 mm × 1.1549 = 0.0336 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 6,349 × 4 × 0.0336 = 853 mm/min (33.5 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (14.29 × 2.38 × 853) / 1000 = 29.01 cm³/min (1.77 in³/min)
Specific Cutting Force (kc) for 4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC): 2100 N/mm². Spindle drive efficiency η = 0.80.

4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC) (3/8" (0.375 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 3/8" (0.375 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 9.53 mm 4.76 mm 1× 277 10.9 12.57 0.55
Slotting (100% WOC) 3F 9.53 mm 4.76 mm 1× 415 16.4 18.83 0.82
Slotting (100% WOC) 4F 9.53 mm 4.76 mm 1× 554 21.8 25.13 1.1
Profiling / HEM (25% WOC) 2F 2.38 mm 14.29 mm 1.1549× 427 16.8 14.52 0.64
Profiling / HEM (25% WOC) 3F 2.38 mm 14.29 mm 1.1549× 640 25.1 21.77 0.95
Profiling / HEM (25% WOC) CURRENT 4F 2.38 mm 14.29 mm 1.1549× 853 33.5 29.01 1.27
Adaptive Clearing (10% WOC) 2F 0.95 mm 19.05 mm 1.6686× 617 24.3 11.17 0.49
Adaptive Clearing (10% WOC) 3F 0.95 mm 19.05 mm 1.6686× 926 36.4 16.76 0.73
Adaptive Clearing (10% WOC) 4F 0.95 mm 19.05 mm 1.6686× 1,234 48.5 22.33 0.98

Shop-Floor Machining Strategy for 4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC)

Work Hardening: Moderate-High
Coolant & Lubrication Protocol

Air Blast for TiAlN Coated Carbide; Flood Coolant for HSS

Pressure: 6 bar air blast or 20 bar high-pressure flood

Thermal shock from erratic coolant flow causes micro-chipping of carbide cutting edges.

Chip Evacuation & Tool Path Guidance

Chip Flow: Short curled chips form with proper feed; excellent surface finish potential.

Milling Direction: Climb milling essential to enter at thickest chip portion.

Expert Machinist Tips:
  • Pre-hardened 4140 (HT) machines cleanly with rigid setups and AlTiN or TiAlN coated tooling.
  • Use high-efficiency milling (HEM): 8-12% ae radial engagement with 1.5x-2.0x ap depth of cut.
  • Keep tool stickout as short as possible to eliminate chatter harmonics.

Frequently Asked CNC Questions (4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC) / 3/8" (0.375 in))

What is the recommended RPM for milling 4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC) with a 3/8" (0.375 in) end mill?
For a 3/8" (0.375 in) (9.525 mm) TiAlN coated carbide end mill in 4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC), the baseline surface cutting speed is 190 m/min (623.4 SFM), which translates to a calculated spindle speed of 6,349 RPM. If using uncoated carbide, reduce surface speed to 150 m/min (500 SFM / 5013 RPM). For HSS cutters, speed must be restricted to 24 m/min (802 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 3/8" (0.375 in) in 4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC)?
At 6,349 RPM with a 4-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0336 mm/tooth (0.00132"/tooth) after applying a radial chip thinning factor (CTF) of 1.1549×. This yields a table feed rate of 853 mm/min (33.5 IPM). Ramping or plunging into material should be limited to 35% of table feed (299 mm/min / 11.7 IPM) at an entry ramp angle of 1.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 2.38 mm), the Chip Thinning Factor is 1.1549×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC)?
Air Blast for TiAlN Coated Carbide; Flood Coolant for HSS. Pressure specification: 6 bar air blast or 20 bar high-pressure flood. Engineering rationale: Thermal shock from erratic coolant flow causes micro-chipping of carbide cutting edges.